IEEE802.3 10BASE-T/100BASE-TX | Toshiba BSA4TMGS12QMR, B-SA4TP

APPENDIX 2 INTERFACE

ENGLISH VERSION EO1-33048

APPENDIX 2 INTERFACE

USB interface

Standard:	Conforming to V2.0 Full speed
Transfer type:	Control transfer, Bulk transfer
Transfer rate:	Full speed (12M bps)
Class:	Printer class
Control mode:	Status with the receive buffer free space information
Number of ports:	1
Power source:	Self power
Connector:	Type B

	Pin No.	Signal
	1	VCC
	2	D-
	3	D+
	3	D+
	4	GND			Series B Plug

LAN

	Standard:	IEEE802.3 10BASE-T/100BASE-TX
	Number of ports:	1
	Connector:	RJ-45					LED	LED Status
	LED status:	Link LED					Link	ON
		Activity LED						OFF
	Link LED (Green)
							Activity	ON


								OFF
	Activity LED (Orange)
	Activity LED (Orange)

LAN status

10Mbps link or 100Mbps link is detected. No link is detected.

*Communication cannot be made while the Link LED is off.

Communicating Idle

LAN cable:	10BASE-T: UTP category 3 or category 5
	100BASE-TX: UTP category 5
Cable length:	Segment length Max. 100 m

NOTES:

1.For IP address setting, refer to Section 2.7.3 IP Address Setting (TCP/IP).

2.When a generally-used twisted pair Ethernet (TPE) or UTP cable is used, a communication error may occur depending on your operating environment. In such case, you may be requested to use a shielded twisted pair cable.

EA2- 3

Image 101

Toshiba BSA4TMGS12QMR, B-SA4TM-GS12-QM-R, B-SA4TP manual IEEE802.3 10BASE-T/100BASE-TX

Contents

SA4TP Series Vorsicht CE Compliance for EU only SA4TP Series Waste Recycling information for users Meanings of Each Symbol Safety Summary Request Regarding Maintenance Precautions Table of Contents EA2-1 EA1-1EA3-1 EA4-1 Product Overview Introduction Features Accessories Appearance DimensionsFront View Rear View Interior Operation Panel Option Name Type Usage Options Setup Flow Printer SetupProcedure Reference Example of US Type InstallationConnecting the Power Cord Take out the Media Holder Ass’y from the printer Loading the MediaRaise the Release Lever and remove the Media Holder Left Insert the Media Shaft into the core of a media roll Place the Media Holder Ass’y into the printer Fold the Release Lever to lock the Media Holder Left Click Upper Sensor Upper SensorLever Ass’y Setting the Feed Gap Sensor position Setting the Black Mark Sensor position Strip mode Option Batch mode Press down the Release Bar to open the Strip Unit Tag paper or Thick paper Cut mode OptionLabel or Thin media Loading the Ribbon Open the Ribbon Cover Gently close the Top Cover until it clicks Cont Connecting the Printer to Your Host Computer Turning the Printer Refer to the B-SA4T Series Key Operation Refer to .3 ResetFine Adjustment SA4T How to Enter the System ModeParameter Setting Baud rate selection Baud Rate „ Serial RS-232C Interface Parity „ Serial RS-232C Interface Data LengthStop Bit „ LCD Message Language Flow ControlREADY/BUSY XON/XOFF „ Parallel Centronics Interface „ Web Printer Function when using TCP/IP LAN „ Plug & Play IP Address Setting TCP/IP This section, how to set the IP address is described IP Address SettingPress the Pause key to enter the IP Address Setting Mode TCP/IP This parameter is to set an IP address Printer IP Address This parameter is to set a Gateway IP address Gateway IP AddressSubnet Mask This parameter is to set a Subnet Mask Dhcp This parameter is to enable DhcpSocket Port Ascii code and Hex. code correspondence table Dhcp Client IDThis parameter is to set a Dhcp client ID General Description Installing the Printer DriversIntroduction Parallel Interface Installing the Printer Driver Windows 95/98/Me Windows NT4.0 Windows 2000/XP Windows 98/Me USB Interface E2-36 E2-37 E2-38 Finish button E2-40 E2-41 E2-42 Uninstalling the Printer Driver Adding a LAN Port Windows 95/98/ME Adding/Deleting a LAN Port Deleting a LAN Port Windows NT4.0/2000/XP Others Printer Driver Upgrades Using the Printer Driver Print Method AdjustmentPrint Test When using an optional Cutter Module or Strip Module 3ADJUST SET Position and Print Tone Fine Adjustment Cut/Strip Position Fine Adjustment Feed Amount Fine AdjustmentReverse Feed Amount Fine Adjustment Coordinate Fine Adjustment Tone Fine When setting +0.0 mmPosition and Print Example of Cut Position Fine Adjustment Example of Strip Position Fine Adjustment Example of Reverse Feed Amount Fine Adjustment When setting +50.0 mm When setting -50.0 mm Print Tone Fine Adjustment Ribbon Motor Voltage Fine Adjustment Sensor type is displayed Threshold Setting Select the sensor to be adjusted by using the Feed key Feed and Pause keys Press the Pause key to enter the Sensor Adjustment Mode „ When using the Black Mark Sensor „ When using the Feed Gap Sensor „ Storing a No Media Level Voltage „ Manual Threshold Setting Black Mark Sensor Feed Gap Sensor Operation Panel On Line OperationUsed to stop printing temporarily Used to restart printing Press and hold the Restart key for 3 seconds or longer ResetOperation Print Head/Platen/ Sensors MaintenanceCleaning Print Head/Platen/ Sensors Covers and Panels Optional Cutter Module 1. Open the Front Cover Same way, clean the outside of the Cutter Blade Backing Paper Feed Roller Strip Roller Guide Roller Restart key TroubleshootingError Messages Error Messages Problems/Cause Possible Problems Causes Solutions Possible Problems Do not use any tool that may damage the Print Head Removing Jammed Media Model Printer SpecificationsThis section describes the printer specifications Mail 4STATE Customer CODE, RSS14 Media Supply SpecificationsMedia Type Label Tag paper with square holes Detection Area of the Transmissive SensorLabel Effective Print Area Detection Area of the Reflective Sensor Media type Description RibbonRecommended Media and Ribbon Types Ribbon type Description Care/Handling of Media and RibbonCombination of Media and Ribbon Media type Vellum paper and label ROM Symbols in the messageAppendix 1 Messages and Leds Base LAN Board is being initialised When the Dhcp function is enabledDhcp client is being initialized Printer did not succeed in writing data Following message appears Parallel interface Centronics Appendix 2 Interface PIN Connector IEEE802.3 10BASE-T/100BASE-TX Awid MPR-1510A-RM SA704-RFID-U1-USSA704-RFID-U1-EU Awid MPR-1580A-RM Snmp Wireless LAN Option At least, 125% of the rated current of the product Appendix 3 Power CordWhen purchasing the power cord Appendix 4 Print Samples Appendix 4 Print Samples JAN13, EAN13 Interleaved 2EAN13+2 digits EAN13+5 digits Industrial 2 UPC-A+5 digitsCustomer bar code KIX Code Appendix 5 Glossaries USB Universal Serial Bus Device used to remove labels from the backing paperMedia and ribbon Index Index EO1-33048