USB Interface, Windows 98/Me | Toshiba B-SA4TM-GS12-QM-R, B-SA4TP

2. PRINTER SETUP

ENGLISH VERSION EO1-33048

2.8 Installing the Printer Drivers

(2)USB INTERFACE

Installation starts by the operating system’s plug-and-play function. Windows 95 and Windows NT4.0 do not support the USB interface.

Windows 98/Me

(1)Turn the printer ON, then connect it to your host computer with the USB cable.

The “New Hardware Found” dialog box is displayed, and “USB Device” is detected.

(2)After a while, the “Add New Hardware Wizard” dialog box is displayed.

Select “Specify the location of the driver (Advanced)”, then click on the [Next] button.

E2-35

Image 48

Toshiba B-SA4TM-GS12-QM-R, B-SA4TP, BSA4TMGS12QMR manual USB Interface, Windows 98/Me

Contents

SA4TP Series CE Compliance for EU only Vorsicht SA4TP Series Waste Recycling information for users Safety Summary Meanings of Each Symbol Precautions Request Regarding Maintenance Table of Contents EA1-1 EA2-1EA3-1 EA4-1 Introduction Features Product Overview Accessories Dimensions AppearanceFront View Rear View Operation Panel Interior Options Option Name Type Usage Printer Setup Setup FlowProcedure Reference Installation Connecting the Power CordExample of US Type Loading the Media Take out the Media Holder Ass’y from the printerRaise the Release Lever and remove the Media Holder Left Insert the Media Shaft into the core of a media roll Fold the Release Lever to lock the Media Holder Left Place the Media Holder Ass’y into the printer Click Upper Sensor Upper SensorLever Ass’y Setting the Feed Gap Sensor position Setting the Black Mark Sensor position Batch mode Strip mode Option Press down the Release Bar to open the Strip Unit Cut mode Option Label or Thin mediaTag paper or Thick paper Loading the Ribbon Open the Ribbon Cover Cont Gently close the Top Cover until it clicks Connecting the Printer to Your Host Computer Turning the Printer Refer to .3 Reset Fine AdjustmentRefer to the B-SA4T Series Key Operation How to Enter the System Mode Parameter SettingSA4T Baud rate selection „ Serial RS-232C Interface Baud Rate „ Serial RS-232C Interface Data Length Stop BitParity Flow Control „ LCD Message LanguageREADY/BUSY XON/XOFF „ Web Printer Function when using TCP/IP LAN „ Parallel Centronics Interface „ Plug & Play IP Address Setting TCP/IP IP Address Setting This section, how to set the IP address is describedPress the Pause key to enter the IP Address Setting Mode TCP/IP Printer IP Address This parameter is to set an IP address Gateway IP Address This parameter is to set a Gateway IP addressSubnet Mask This parameter is to set a Subnet Mask This parameter is to enable Dhcp Socket PortDhcp Dhcp Client ID This parameter is to set a Dhcp client IDAscii code and Hex. code correspondence table Installing the Printer Drivers IntroductionGeneral Description Installing the Printer Driver Parallel Interface Windows 95/98/Me Windows NT4.0 Windows 2000/XP USB Interface Windows 98/Me E2-36 E2-37 E2-38 Finish button E2-40 E2-41 E2-42 Uninstalling the Printer Driver Adding/Deleting a LAN Port Adding a LAN Port Windows 95/98/ME Windows NT4.0/2000/XP Deleting a LAN Port Printer Driver Upgrades Others Using the Printer Driver Adjustment Print TestPrint Method When using an optional Cutter Module or Strip Module Position and Print Tone Fine Adjustment 3ADJUST SET Feed Amount Fine Adjustment Cut/Strip Position Fine AdjustmentReverse Feed Amount Fine Adjustment Coordinate Fine Adjustment When setting +0.0 mm Position and PrintTone Fine Example of Cut Position Fine Adjustment Example of Strip Position Fine Adjustment Example of Reverse Feed Amount Fine Adjustment When setting -50.0 mm When setting +50.0 mm Print Tone Fine Adjustment Ribbon Motor Voltage Fine Adjustment Threshold Setting Sensor type is displayed Select the sensor to be adjusted by using the Feed key Press the Pause key to enter the Sensor Adjustment Mode Feed and Pause keys „ When using the Black Mark Sensor „ When using the Feed Gap Sensor „ Manual Threshold Setting „ Storing a No Media Level Voltage Black Mark Sensor Feed Gap Sensor On Line Operation Operation PanelUsed to stop printing temporarily Used to restart printing Reset OperationPress and hold the Restart key for 3 seconds or longer Maintenance CleaningPrint Head/Platen/ Sensors Print Head/Platen/ Sensors Covers and Panels Same way, clean the outside of the Cutter Blade Optional Cutter Module 1. Open the Front Cover Backing Paper Feed Roller Strip Roller Guide Roller Troubleshooting Error MessagesRestart key Error Messages Problems/Cause Possible Problems Possible Problems Causes Solutions Removing Jammed Media Do not use any tool that may damage the Print Head Printer Specifications This section describes the printer specificationsModel Mail 4STATE Customer CODE, RSS14 Supply Specifications MediaMedia Type Label Detection Area of the Transmissive Sensor LabelTag paper with square holes Detection Area of the Reflective Sensor Effective Print Area Ribbon Recommended Media and Ribbon TypesMedia type Description Care/Handling of Media and Ribbon Ribbon type DescriptionCombination of Media and Ribbon Media type Vellum paper and label Symbols in the message Appendix 1 Messages and LedsROM When the Dhcp function is enabled Base LAN Board is being initialisedDhcp client is being initialized Printer did not succeed in writing data Following message appears Appendix 2 Interface Parallel interface Centronics Connector PIN IEEE802.3 10BASE-T/100BASE-TX SA704-RFID-U1-US Awid MPR-1510A-RMSA704-RFID-U1-EU Awid MPR-1580A-RM Wireless LAN Option Snmp Appendix 3 Power Cord When purchasing the power cordAt least, 125% of the rated current of the product Appendix 4 Print Samples Appendix 4 Print Samples Interleaved 2 JAN13, EAN13EAN13+2 digits EAN13+5 digits UPC-A+5 digits Industrial 2Customer bar code KIX Code Appendix 5 Glossaries Device used to remove labels from the backing paper Media and ribbonUSB Universal Serial Bus Index Index EO1-33048