Manuals / Toshiba / Computer Equipment / Printer

Toshiba B-SA4TP manual On Line Operation, Operation Panel, Used to stop printing temporarily

Models: B-SA4TP B-SA4TM-GS12-QM-R BSA4TMGS12QMR

1 113

Download 113 pages 21.72 Kb

Page 79

3. ON LINE OPERATION

ENGLISH VERSION EO1-33048

3.1 Operation Panel

3. ON LINE OPERATION

3.1 Operation Panel

This chapter describes usage of the keys on the Operation Panel in On Line mode.

When the printer is in On Line mode and connected to a host computer, the normal operation of printing images on labels or tags can be accomplished.

The figure below illustrates the Operation Panel and key functions.

ON LINE LED (Green)

[FEED] key

LCD Message

Display

ERROR LED (Red)

[PAUSE] key

[RESTART] key

NOTES:

1.Flashes only when the Ribbon Near End Detection function is selected.

2.Use the [RESTART] key to resume printing after a pause, or after clearing an error.

The LCD Message Display shows messages in alphanumeric characters and symbols to indicate the printer’s current status. Up to 32 characters can be displayed on two lines.

There are two LEDs on the Operation Panel.

LED	Illuminates when…	Flashes when…
ON LINE	The printer is ready to	The printer is
	print.	communicating with
		your computer.
ERROR	Any error occurs with	The ribbon is nearly
	the printer.	over. (See NOTE 1.)

There are three keys on the operation panel.

PAUSE	Used to stop printing temporarily.
RESTART	Used to restart printing.
FEED	Used to feed media.

E3- 1

Image 79

Toshiba B-SA4TP manual On Line Operation, Operation Panel, Used to stop printing temporarily, Used to restart printing

Contents

SA4TP Series Vorsicht CE Compliance for EU only SA4TP Series Waste Recycling information for users Meanings of Each Symbol Safety Summary Request Regarding Maintenance Precautions Table of Contents EA4-1 EA1-1EA2-1 EA3-1 Product Overview Introduction Features Accessories Rear View DimensionsAppearance Front View Interior Operation Panel Option Name Type Usage Options Reference Printer SetupSetup Flow Procedure Connecting the Power Cord InstallationExample of US Type Insert the Media Shaft into the core of a media roll Loading the MediaTake out the Media Holder Ass’y from the printer Raise the Release Lever and remove the Media Holder Left Place the Media Holder Ass’y into the printer Fold the Release Lever to lock the Media Holder Left Click Upper Sensor Upper SensorLever Ass’y Setting the Feed Gap Sensor position Setting the Black Mark Sensor position Strip mode Option Batch mode Press down the Release Bar to open the Strip Unit Label or Thin media Cut mode OptionTag paper or Thick paper Loading the Ribbon Open the Ribbon Cover Gently close the Top Cover until it clicks Cont Connecting the Printer to Your Host Computer Turning the Printer Fine Adjustment Refer to .3 ResetRefer to the B-SA4T Series Key Operation Parameter Setting How to Enter the System ModeSA4T Baud rate selection Baud Rate „ Serial RS-232C Interface Stop Bit „ Serial RS-232C Interface Data LengthParity XON/XOFF Flow Control„ LCD Message Language READY/BUSY „ Parallel Centronics Interface „ Web Printer Function when using TCP/IP LAN „ Plug & Play IP Address Setting TCP/IP TCP/IP IP Address SettingThis section, how to set the IP address is described Press the Pause key to enter the IP Address Setting Mode This parameter is to set an IP address Printer IP Address This parameter is to set a Subnet Mask Gateway IP AddressThis parameter is to set a Gateway IP address Subnet Mask Socket Port This parameter is to enable DhcpDhcp This parameter is to set a Dhcp client ID Dhcp Client IDAscii code and Hex. code correspondence table Introduction Installing the Printer DriversGeneral Description Parallel Interface Installing the Printer Driver Windows 95/98/Me Windows NT4.0 Windows 2000/XP Windows 98/Me USB Interface E2-36 E2-37 E2-38 Finish button E2-40 E2-41 E2-42 Uninstalling the Printer Driver Adding a LAN Port Windows 95/98/ME Adding/Deleting a LAN Port Deleting a LAN Port Windows NT4.0/2000/XP Others Printer Driver Upgrades Using the Printer Driver Print Test AdjustmentPrint Method When using an optional Cutter Module or Strip Module 3ADJUST SET Position and Print Tone Fine Adjustment Coordinate Fine Adjustment Feed Amount Fine AdjustmentCut/Strip Position Fine Adjustment Reverse Feed Amount Fine Adjustment Position and Print When setting +0.0 mmTone Fine Example of Cut Position Fine Adjustment Example of Strip Position Fine Adjustment Example of Reverse Feed Amount Fine Adjustment When setting +50.0 mm When setting -50.0 mm Print Tone Fine Adjustment Ribbon Motor Voltage Fine Adjustment Sensor type is displayed Threshold Setting Select the sensor to be adjusted by using the Feed key Feed and Pause keys Press the Pause key to enter the Sensor Adjustment Mode „ When using the Black Mark Sensor „ When using the Feed Gap Sensor „ Storing a No Media Level Voltage „ Manual Threshold Setting Black Mark Sensor Feed Gap Sensor Used to restart printing On Line OperationOperation Panel Used to stop printing temporarily Operation ResetPress and hold the Restart key for 3 seconds or longer Cleaning MaintenancePrint Head/Platen/ Sensors Print Head/Platen/ Sensors Covers and Panels Optional Cutter Module 1. Open the Front Cover Same way, clean the outside of the Cutter Blade Backing Paper Feed Roller Strip Roller Guide Roller Error Messages TroubleshootingRestart key Error Messages Problems/Cause Possible Problems Causes Solutions Possible Problems Do not use any tool that may damage the Print Head Removing Jammed Media This section describes the printer specifications Printer SpecificationsModel Mail 4STATE Customer CODE, RSS14 Label Supply SpecificationsMedia Media Type Label Detection Area of the Transmissive SensorTag paper with square holes Effective Print Area Detection Area of the Reflective Sensor Recommended Media and Ribbon Types RibbonMedia type Description Media type Vellum paper and label Care/Handling of Media and RibbonRibbon type Description Combination of Media and Ribbon Appendix 1 Messages and Leds Symbols in the messageROM Printer did not succeed in writing data When the Dhcp function is enabledBase LAN Board is being initialised Dhcp client is being initialized Following message appears Parallel interface Centronics Appendix 2 Interface PIN Connector IEEE802.3 10BASE-T/100BASE-TX Awid MPR-1580A-RM SA704-RFID-U1-USAwid MPR-1510A-RM SA704-RFID-U1-EU Snmp Wireless LAN Option When purchasing the power cord Appendix 3 Power CordAt least, 125% of the rated current of the product Appendix 4 Print Samples Appendix 4 Print Samples EAN13+5 digits Interleaved 2JAN13, EAN13 EAN13+2 digits KIX Code UPC-A+5 digitsIndustrial 2 Customer bar code Appendix 5 Glossaries Media and ribbon Device used to remove labels from the backing paperUSB Universal Serial Bus Index Index EO1-33048