![](/images/new-backgrounds/1264301/264301181x1.webp)
7. SUPPLY SPECIFICATIONS
ENGLISH VERSION
7.1 Media
7. SUPPLY SPECIFICATIONS
7.1 Media
Please make sure that the media being used is approved by TOSHIBA TEC. The warranty does not apply when a problem is caused by using media that is not approved by TOSHIBA TEC.
For information regarding TOSHIBA TEC approved media, please contact a TOSHIBA TEC authorised service representative.
7.1.1 Media Type
Two types of media can be loaded for this thermal transfer and direct thermal printer: label or tag. The table below shows size and shape of the media available for this printer.
| Black Mark |
| Black Mark |
Label | (on reverse side) | Tag paper | (on reverse side) |
|
Stop position k
Cut position
j
i f e
Stop |
| |
position k |
| |
h g | h | |
Cut position |
| |
c | c | |
d | ||
| ||
| i | |
Feed Direction | e | |
| [Unit: mm] |
| Label dispensing mode | Batch mode | Strip mode | Cut mode | |||
Item |
| ||||||
|
|
|
|
| |||
c Media pitch | Thermal direct | 10.0 – 999.0 | 19.0 | – 999.0 | 19.0 - 999.0 | ||
Thermal transfer | 15.0 – 999.0 | ||||||
|
|
|
|
| |||
d Label length | Thermal direct | 8.0 – 997.0 | 17.0 | – 997.0 | 16.0 – 997.0 | ||
Thermal transfer | 13.0 – 997.0 | ||||||
|
|
|
|
| |||
e Media width/backing paper width | Thermal direct |
| 25.0 | – 118.0 |
| ||
Thermal transfer |
| 25.0 | – 114.0 |
| |||
|
|
|
| ||||
f Label width | Thermal direct |
| 22.0 | – 115.0 |
| ||
Thermal transfer |
| 22.0 | – 111.0 |
| |||
|
|
|
| ||||
g Gap length |
| 2.0 – 20.0 | 2.0 – 5.0 | 3.0 – 20.0 | |||
h Black mark length (Tag paper) |
|
| 2.0 | – 10.0 |
| ||
i Maximum effective print width |
| 104.0 | |||||
| Label | Thermal direct | 6.0 – 995.0 | 15.0 | – 995.0 | 14.0 - 995.0 | |
j Effective print length | Thermal transfer | 11.0 – 995.0 | |||||
|
|
|
| ||||
Tag paper | Thermal direct | 8.0 – 997.0 | 17.0 – 997.0 | ||||
| |||||||
| Thermal transfer | 13.0 – 997.0 | |||||
|
|
|
|
| |||
k Print speed up/slow down area |
|
|
| 1.0 |
| ||
Thickness | Thermal direct | 0.08 – 0.17 (Note 4) | 0.13 – 0.17 | 0.08 – 0.17 (Note 4) | |||
Thermal transfer | 0.1 – 0.17 (Note 4) | 0.13 – 0.17 | 0.1 – 0.17 (Note 4) | ||||
|
| ||||||
Maximum outer roll diameter |
|
| Ø152.4 |
| |||
Roll direction |
|
| Inside/Outside |
| |||
Inner core diameter |
|
| Ø38, 40, 42, 76.2±0.3 |
|
E7- 1