Appearance, Dimensions, Front View | Toshiba BSA4TMGS12QMR, B-SA4TP

1. PRODUCT OVERVIEW

ENGLISH VERSION EO1-33048

1.4 Appearance

1.4 Appearance

The names of the parts or units introduced in this section are used in the following chapters.

238 (9.4)

339 (13.3)

1.4.1 Dimensions

332

(13.1)

1.4.2 Front View

Ribbon Cover

Top Cover

LCD Message

Display

Operation Panel

Power Switch

O: OFF

I: ON

1.4.3 Rear View

Supply Window

AC Power Inlet

Dimensions in mm (inches)

Top Cover

Release Button

Media Outlet

Front Cover

RS-232C Serial Interface Connector (Option)

Wireless LAN Interface Board (Option)

Parallel Interface Connector (Centronics)

USB Interface

Connector

LAN Interface

Connector

E1- 3

Image 11

Toshiba BSA4TMGS12QMR, B-SA4TM-GS12-QM-R, B-SA4TP manual Appearance, Dimensions, Front View, Rear View

Contents

SA4TP Series Vorsicht CE Compliance for EU only SA4TP Series Waste Recycling information for users Meanings of Each Symbol Safety Summary Request Regarding Maintenance Precautions Table of Contents EA4-1 EA1-1EA2-1 EA3-1 Product Overview Introduction Features Accessories Rear View DimensionsAppearance Front View Interior Operation Panel Option Name Type Usage Options Reference Printer SetupSetup Flow Procedure Example of US Type InstallationConnecting the Power Cord Insert the Media Shaft into the core of a media roll Loading the MediaTake out the Media Holder Ass’y from the printer Raise the Release Lever and remove the Media Holder Left Place the Media Holder Ass’y into the printer Fold the Release Lever to lock the Media Holder Left Click Upper Sensor Upper SensorLever Ass’y Setting the Feed Gap Sensor position Setting the Black Mark Sensor position Strip mode Option Batch mode Press down the Release Bar to open the Strip Unit Tag paper or Thick paper Cut mode OptionLabel or Thin media Loading the Ribbon Open the Ribbon Cover Gently close the Top Cover until it clicks Cont Connecting the Printer to Your Host Computer Turning the Printer Refer to the B-SA4T Series Key Operation Refer to .3 ResetFine Adjustment SA4T How to Enter the System ModeParameter Setting Baud rate selection Baud Rate „ Serial RS-232C Interface Parity „ Serial RS-232C Interface Data LengthStop Bit XON/XOFF Flow Control„ LCD Message Language READY/BUSY „ Parallel Centronics Interface „ Web Printer Function when using TCP/IP LAN „ Plug & Play IP Address Setting TCP/IP TCP/IP IP Address SettingThis section, how to set the IP address is described Press the Pause key to enter the IP Address Setting Mode This parameter is to set an IP address Printer IP Address This parameter is to set a Subnet Mask Gateway IP AddressThis parameter is to set a Gateway IP address Subnet Mask Dhcp This parameter is to enable DhcpSocket Port Ascii code and Hex. code correspondence table Dhcp Client IDThis parameter is to set a Dhcp client ID General Description Installing the Printer DriversIntroduction Parallel Interface Installing the Printer Driver Windows 95/98/Me Windows NT4.0 Windows 2000/XP Windows 98/Me USB Interface E2-36 E2-37 E2-38 Finish button E2-40 E2-41 E2-42 Uninstalling the Printer Driver Adding a LAN Port Windows 95/98/ME Adding/Deleting a LAN Port Deleting a LAN Port Windows NT4.0/2000/XP Others Printer Driver Upgrades Using the Printer Driver Print Method AdjustmentPrint Test When using an optional Cutter Module or Strip Module 3ADJUST SET Position and Print Tone Fine Adjustment Coordinate Fine Adjustment Feed Amount Fine AdjustmentCut/Strip Position Fine Adjustment Reverse Feed Amount Fine Adjustment Tone Fine When setting +0.0 mmPosition and Print Example of Cut Position Fine Adjustment Example of Strip Position Fine Adjustment Example of Reverse Feed Amount Fine Adjustment When setting +50.0 mm When setting -50.0 mm Print Tone Fine Adjustment Ribbon Motor Voltage Fine Adjustment Sensor type is displayed Threshold Setting Select the sensor to be adjusted by using the Feed key Feed and Pause keys Press the Pause key to enter the Sensor Adjustment Mode „ When using the Black Mark Sensor „ When using the Feed Gap Sensor „ Storing a No Media Level Voltage „ Manual Threshold Setting Black Mark Sensor Feed Gap Sensor Used to restart printing On Line OperationOperation Panel Used to stop printing temporarily Press and hold the Restart key for 3 seconds or longer ResetOperation Print Head/Platen/ Sensors MaintenanceCleaning Print Head/Platen/ Sensors Covers and Panels Optional Cutter Module 1. Open the Front Cover Same way, clean the outside of the Cutter Blade Backing Paper Feed Roller Strip Roller Guide Roller Restart key TroubleshootingError Messages Error Messages Problems/Cause Possible Problems Causes Solutions Possible Problems Do not use any tool that may damage the Print Head Removing Jammed Media Model Printer SpecificationsThis section describes the printer specifications Mail 4STATE Customer CODE, RSS14 Label Supply SpecificationsMedia Media Type Tag paper with square holes Detection Area of the Transmissive SensorLabel Effective Print Area Detection Area of the Reflective Sensor Media type Description RibbonRecommended Media and Ribbon Types Media type Vellum paper and label Care/Handling of Media and RibbonRibbon type Description Combination of Media and Ribbon ROM Symbols in the messageAppendix 1 Messages and Leds Printer did not succeed in writing data When the Dhcp function is enabledBase LAN Board is being initialised Dhcp client is being initialized Following message appears Parallel interface Centronics Appendix 2 Interface PIN Connector IEEE802.3 10BASE-T/100BASE-TX Awid MPR-1580A-RM SA704-RFID-U1-USAwid MPR-1510A-RM SA704-RFID-U1-EU Snmp Wireless LAN Option At least, 125% of the rated current of the product Appendix 3 Power CordWhen purchasing the power cord Appendix 4 Print Samples Appendix 4 Print Samples EAN13+5 digits Interleaved 2JAN13, EAN13 EAN13+2 digits KIX Code UPC-A+5 digitsIndustrial 2 Customer bar code Appendix 5 Glossaries USB Universal Serial Bus Device used to remove labels from the backing paperMedia and ribbon Index Index EO1-33048