Manuals / Toshiba / Computer Equipment / Printer

Toshiba B-SA4TM-GS12-QM-R, B-SA4TP, BSA4TMGS12QMR manual Click Upper Sensor Upper SensorLever Ass’y

Models: B-SA4TP B-SA4TM-GS12-QM-R BSA4TMGS12QMR

1 113

Download 113 pages 21.72 Kb

Page 18

2. PRINTER SETUP

ENGLISH VERSION EO1-33048

2.3 Loading the Media

2.3Loading the Media (Cont.)

CAUTION!

Be sure to close the Upper Sensor Ass’y before closing the Top Cover. If the Upper Sensor Ass’y is opened, it may be damaged.

NOTE:

Make sure that the Upper Sensor Ass’y is locked. If it is unlocked, a paper jam or print failure may occur.

9.Pull the media out of the front of the printer, and adjust the Media Guides to the media width. This will automatically centre the media.

Media Guide

10.Lower the Upper Sensor Ass’y until the Upper Sensor Lever clicks into position.

Click

Upper Sensor

Upper SensorLever

Ass’y

E2- 5

Image 18

Toshiba B-SA4TM-GS12-QM-R, B-SA4TP, BSA4TMGS12QMR manual Click Upper Sensor Upper SensorLever Ass’y

Contents

SA4TP Series CE Compliance for EU only Vorsicht SA4TP Series Waste Recycling information for users Safety Summary Meanings of Each Symbol Precautions Request Regarding Maintenance Table of Contents EA3-1 EA1-1EA2-1 EA4-1 Introduction Features Product Overview Accessories Front View DimensionsAppearance Rear View Operation Panel Interior Options Option Name Type Usage Procedure Printer SetupSetup Flow Reference Installation Connecting the Power CordExample of US Type Raise the Release Lever and remove the Media Holder Left Loading the MediaTake out the Media Holder Ass’y from the printer Insert the Media Shaft into the core of a media roll Fold the Release Lever to lock the Media Holder Left Place the Media Holder Ass’y into the printer Click Upper Sensor Upper SensorLever Ass’y Setting the Feed Gap Sensor position Setting the Black Mark Sensor position Batch mode Strip mode Option Press down the Release Bar to open the Strip Unit Cut mode Option Label or Thin mediaTag paper or Thick paper Loading the Ribbon Open the Ribbon Cover Cont Gently close the Top Cover until it clicks Connecting the Printer to Your Host Computer Turning the Printer Refer to .3 Reset Fine AdjustmentRefer to the B-SA4T Series Key Operation How to Enter the System Mode Parameter SettingSA4T Baud rate selection „ Serial RS-232C Interface Baud Rate „ Serial RS-232C Interface Data Length Stop BitParity READY/BUSY Flow Control„ LCD Message Language XON/XOFF „ Web Printer Function when using TCP/IP LAN „ Parallel Centronics Interface „ Plug & Play IP Address Setting TCP/IP Press the Pause key to enter the IP Address Setting Mode IP Address SettingThis section, how to set the IP address is described TCP/IP Printer IP Address This parameter is to set an IP address Subnet Mask Gateway IP AddressThis parameter is to set a Gateway IP address This parameter is to set a Subnet Mask This parameter is to enable Dhcp Socket PortDhcp Dhcp Client ID This parameter is to set a Dhcp client IDAscii code and Hex. code correspondence table Installing the Printer Drivers IntroductionGeneral Description Installing the Printer Driver Parallel Interface Windows 95/98/Me Windows NT4.0 Windows 2000/XP USB Interface Windows 98/Me E2-36 E2-37 E2-38 Finish button E2-40 E2-41 E2-42 Uninstalling the Printer Driver Adding/Deleting a LAN Port Adding a LAN Port Windows 95/98/ME Windows NT4.0/2000/XP Deleting a LAN Port Printer Driver Upgrades Others Using the Printer Driver Adjustment Print TestPrint Method When using an optional Cutter Module or Strip Module Position and Print Tone Fine Adjustment 3ADJUST SET Reverse Feed Amount Fine Adjustment Feed Amount Fine AdjustmentCut/Strip Position Fine Adjustment Coordinate Fine Adjustment When setting +0.0 mm Position and PrintTone Fine Example of Cut Position Fine Adjustment Example of Strip Position Fine Adjustment Example of Reverse Feed Amount Fine Adjustment When setting -50.0 mm When setting +50.0 mm Print Tone Fine Adjustment Ribbon Motor Voltage Fine Adjustment Threshold Setting Sensor type is displayed Select the sensor to be adjusted by using the Feed key Press the Pause key to enter the Sensor Adjustment Mode Feed and Pause keys „ When using the Black Mark Sensor „ When using the Feed Gap Sensor „ Manual Threshold Setting „ Storing a No Media Level Voltage Black Mark Sensor Feed Gap Sensor Used to stop printing temporarily On Line OperationOperation Panel Used to restart printing Reset OperationPress and hold the Restart key for 3 seconds or longer Maintenance CleaningPrint Head/Platen/ Sensors Print Head/Platen/ Sensors Covers and Panels Same way, clean the outside of the Cutter Blade Optional Cutter Module 1. Open the Front Cover Backing Paper Feed Roller Strip Roller Guide Roller Troubleshooting Error MessagesRestart key Error Messages Problems/Cause Possible Problems Possible Problems Causes Solutions Removing Jammed Media Do not use any tool that may damage the Print Head Printer Specifications This section describes the printer specificationsModel Mail 4STATE Customer CODE, RSS14 Media Type Supply SpecificationsMedia Label Detection Area of the Transmissive Sensor LabelTag paper with square holes Detection Area of the Reflective Sensor Effective Print Area Ribbon Recommended Media and Ribbon TypesMedia type Description Combination of Media and Ribbon Care/Handling of Media and RibbonRibbon type Description Media type Vellum paper and label Symbols in the message Appendix 1 Messages and LedsROM Dhcp client is being initialized When the Dhcp function is enabledBase LAN Board is being initialised Printer did not succeed in writing data Following message appears Appendix 2 Interface Parallel interface Centronics Connector PIN IEEE802.3 10BASE-T/100BASE-TX SA704-RFID-U1-EU SA704-RFID-U1-USAwid MPR-1510A-RM Awid MPR-1580A-RM Wireless LAN Option Snmp Appendix 3 Power Cord When purchasing the power cordAt least, 125% of the rated current of the product Appendix 4 Print Samples Appendix 4 Print Samples EAN13+2 digits Interleaved 2JAN13, EAN13 EAN13+5 digits Customer bar code UPC-A+5 digitsIndustrial 2 KIX Code Appendix 5 Glossaries Device used to remove labels from the backing paper Media and ribbonUSB Universal Serial Bus Index Index EO1-33048