Toshiba B-SX600 specs

The following information is for EU-member states only: Disposal of products

(based on EU-Directive 2002/96/EC,

Directive on Waste electrical and electronic equipment – WEEE)

The use of the symbol indicates that this product may not be disposed as unsorted municipal waste and has to be collected separately. Integrated batteries and accumulators can be disposed of with the product. They will be separated at the recycling centers.

The black bar indicates that the product was placed on the market after August 13, 2005.

By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environmental and human health, which could otherwise be caused by inappropriate waste handling of this product.

For more detailed information about the take-back and recycling of this product, please contact your supplier where you purchased this product.

Image 108

Toshiba B-SX600 manual

Contents

SX600 Series CE Compliance for EU only Vorsicht Safety Summary Meanings of Each Symbol Precautions Table of Contents Test Print Specifications Product Overview Introduction Accessories CD-ROM Part Names and Functions Front View USB Interface Connector AC Power Inlet Fanfold Paper SlotRear View Model with a USB interface Ventilation Slot LAN Interface Connector Rear View Model with a LAN interface Interior Media End Sensor Reflective Media Sensor Media HolderMedia Roll Damper Platen Media Roll Guide Media Guide Print Head Upper Unit Upper Unit Handle Ribbon Tensioner Upper Unit Unlock Lever Cancel key Operation PanelMenu key Cutter Unit Cut position Precautions when using the Cutter Unit Peel-off Unit Part names Precautions when using the Peel-off Unit Supplemental Remarks Printer Setup PrecautionsRemoving the Protective Materials Printer Setup Printer Setup Installation Location 40 C Connecting the Power Cord Example of US Type Connecting the Printer with a USB Interface to Your Computer Connecting the Printer with a LAN Interface to Your Computer Supply Specifications Strip mode Cut modeMedia and Ribbon Die-cut label Notched media Label with black marks Guaranteed Print Area When you purchase media and ribbons Storage of Media and RibbonsUnacceptable Media and Ribbons Preprinted Media Media and Ribbon Precaution Loading the Ribbon Release button Gently squeeze the metal. plate Precautions How to Load the Media Loading the Media Loading the Media Low Supplemental Remarks How to Load the Media for the Model with the Peel-off Unit Please read .1 How to Load the Media first Precautions Loading the Media Loading the Media How to Load a Narrow Label Stock How to Reload the Media when the Upper Unit is Lifted How to Load Fanfold Paper Printing from Your Computer Print Test from Printer Driver Printing from Your Computer Printing from Your Computer Precautions when Using the Model with a LAN Interface Printing from Your Computer Media Feed Mode Fixed Length feed modeStrict feed mode Easy feed mode Printer Operation Printer Operation Tear-off Alignment Alignment is performed Alignment when Precise print mode is selected Alignment when Paper saving mode is selected Alignment when Fixed Length feed mode is selected Media Calibration How to perform a media calibration Printer Operation Printer Operation Operation Panel Operation Panel Messages Displayed on the Operation Panel Display when Pause is shown Display when Printing is shown Error messages in the event of End of paper Display in Low Power Mode Printer Operation using the Operation Panel Operation Operational procedures→ See .4 Menu Options Menu Options Information Title Description Trip Reprint Error Page menu Clear Trip Meter menuTest print menu Low Power min Conditions Beep Volume How to Cancel a Print Job Operation Panel How to Perform a Print Test Test PrintPrint Test Pattern Removing Jammed Media Removing Jammed Media from the Cutter Unit Removing Jammed Media from the Peel-off Unit Daily Maintenance Cleaning the Media Sensor Cleaning the Platen Cleaning the Ribbon Separation Plate Cleaning the Ribbon Guide Bar Cleaning the Print Head Cleaning the Peel-off Unit Troubleshooting Problems at Start-up of the PrinterProblems while Printing Printing does not start ⇒2.4 or 2.5 Connecting the Printer to Your ⇒8.5 How to Cancel a Print JobComputer ⇒ 3.7 Unacceptable Media and Ribbons ⇒ 11.3 Cleaning the Ribbon Separation Plate Blank page label is ejectedLoaded ribbon is torn or ejected with the media Print Failure An entire or a part of printout is lightPrinted text is blurred ⇒ 2.2 Installation Location Printouts have streaky smudges or fine lines ⇒ 7.1 Media Feed Mode Print position gradually misaligns⇒ 7.4 Media Calibration ⇒ 8.5 How to Cancel a Print Job ⇒ Help on the Printing Preferences Problems in the Network Model with a LAN Interface ⇒ 2.5 Connecting the Printer to Your Computer Error messages and remedial measures How to Load the Media ⇒ 1.5.2 Precaution when using the Peel-off Unit⇒ 1.4.2 Precautions when using the Cutter Unit Peeling failed Error messages Possible causes Solutions Info. Error Action Info.ErrorImage Info.Error Possible causes Solutions Bad thermal head Frequently Asked Questions FAQ How can I use the printer with the covers left open?Can I use an ink ribbon narrower than a label? Ribbon is torn apart during printing. What should I do? Peeling failure occurs more frequently than before Frequently Asked Questions FAQ Standard model Remarks Specifications SpecificationsPrinter Model with a USB Interface Printer Model with a LAN Interface Http Snmp Simple Network Management Protocol Specifications Cutter Unit Power Cord When purchasing the power cordPage EO1-33085