Label with black marks | Toshiba B-SX600 manual

3. MEDIA AND RIBBON

3.4 Label with black marks

“Label with black marks” refers to a label stock with black marks printed at the back of the backing paper for the position detection purpose, as illustrated below. When a label stock with black marks is loaded, the Reflective Media Sensor is used.

15 to 120 mm

12 mm or over

2 to 13 mm

Label pitch

10 to 1,000 mm

Black mark on the reverse side

Page start line

Reflective Media Sensor (Located under the media)

Media feed direction

3- 4

Image 30

Toshiba B-SX600 manual Label with black marks

Contents

SX600 Series CE Compliance for EU only Vorsicht Safety Summary Meanings of Each Symbol Precautions Table of Contents Test Print Specifications Product Overview Introduction Accessories CD-ROM Part Names and Functions Front View Rear View Model with a USB interface USB Interface ConnectorAC Power Inlet Fanfold Paper Slot Ventilation Slot LAN Interface Connector Rear View Model with a LAN interface Media Roll Damper Platen Media Roll Guide InteriorMedia End Sensor Reflective Media Sensor Media Holder Media Guide Print Head Upper Unit Upper Unit Handle Ribbon Tensioner Upper Unit Unlock Lever Cancel key Operation PanelMenu key Cutter Unit Cut position Precautions when using the Cutter Unit Peel-off Unit Part names Precautions when using the Peel-off Unit Supplemental Remarks Printer Setup PrecautionsRemoving the Protective Materials Printer Setup Printer Setup Installation Location 40 C Connecting the Power Cord Example of US Type Connecting the Printer with a USB Interface to Your Computer Connecting the Printer with a LAN Interface to Your Computer Supply Specifications Strip mode Cut modeMedia and Ribbon Die-cut label Notched media Label with black marks Guaranteed Print Area Unacceptable Media and Ribbons When you purchase media and ribbonsStorage of Media and Ribbons Preprinted Media Media and Ribbon Precaution Loading the Ribbon Release button Gently squeeze the metal. plate Precautions How to Load the Media Loading the Media Loading the Media Low Supplemental Remarks How to Load the Media for the Model with the Peel-off Unit Please read .1 How to Load the Media first Precautions Loading the Media Loading the Media How to Load a Narrow Label Stock How to Reload the Media when the Upper Unit is Lifted How to Load Fanfold Paper Printing from Your Computer Print Test from Printer Driver Printing from Your Computer Printing from Your Computer Precautions when Using the Model with a LAN Interface Printing from Your Computer Strict feed mode Media Feed ModeFixed Length feed mode Easy feed mode Printer Operation Printer Operation Tear-off Alignment Alignment is performed Alignment when Precise print mode is selected Alignment when Paper saving mode is selected Alignment when Fixed Length feed mode is selected Media Calibration How to perform a media calibration Printer Operation Printer Operation Operation Panel Operation Panel Messages Displayed on the Operation Panel Display when Pause is shown Display when Printing is shown Error messages in the event of End of paper Display in Low Power Mode Printer Operation using the Operation Panel Operation Operational procedures→ See .4 Menu Options Menu Options Information Title Description Trip Reprint Error Page menu Clear Trip Meter menuTest print menu Low Power min Conditions Beep Volume How to Cancel a Print Job Operation Panel How to Perform a Print Test Test PrintPrint Test Pattern Removing Jammed Media Removing Jammed Media from the Cutter Unit Removing Jammed Media from the Peel-off Unit Daily Maintenance Cleaning the Media Sensor Cleaning the Platen Cleaning the Ribbon Separation Plate Cleaning the Ribbon Guide Bar Cleaning the Print Head Cleaning the Peel-off Unit Problems while Printing TroubleshootingProblems at Start-up of the Printer Printing does not start Computer ⇒2.4 or 2.5 Connecting the Printer to Your⇒8.5 How to Cancel a Print Job ⇒ 3.7 Unacceptable Media and Ribbons ⇒ 11.3 Cleaning the Ribbon Separation Plate Blank page label is ejectedLoaded ribbon is torn or ejected with the media Print Failure An entire or a part of printout is lightPrinted text is blurred ⇒ 2.2 Installation Location Printouts have streaky smudges or fine lines ⇒ 7.1 Media Feed Mode Print position gradually misaligns⇒ 7.4 Media Calibration ⇒ 8.5 How to Cancel a Print Job ⇒ Help on the Printing Preferences Problems in the Network Model with a LAN Interface ⇒ 2.5 Connecting the Printer to Your Computer Error messages and remedial measures ⇒ 1.4.2 Precautions when using the Cutter Unit How to Load the Media⇒ 1.5.2 Precaution when using the Peel-off Unit Peeling failed Image Info.Error Error messages Possible causes Solutions Info. ErrorAction Info.Error Possible causes Solutions Bad thermal head Frequently Asked Questions FAQ How can I use the printer with the covers left open?Can I use an ink ribbon narrower than a label? Ribbon is torn apart during printing. What should I do? Peeling failure occurs more frequently than before Frequently Asked Questions FAQ Standard model Remarks Specifications SpecificationsPrinter Model with a USB Interface Printer Model with a LAN Interface Http Snmp Simple Network Management Protocol Specifications Cutter Unit Power Cord When purchasing the power cordPage EO1-33085