Printing from Your Computer | Toshiba B-SX600 specs

6. PRINTING FROM YOUR COMPUTER

If LPR is selected for print protocol, open the “B-SX600-HS11-QM-R Printing Preferences” dialog box, click the [Device Settings] tab, and remove the check from the “Obtain printer information” checkbox.

If printing is performed with LPR selected for print protocol and the “Obtain printer information” checkbox checked, subsequent printing may fail.

The printer (with a LAN interface) must be on the same network segment as the computer on which such utilities as Quick Setup and Printserver Version Up Tool (for the model with a LAN interface) run.

If the computer and the printer (with a LAN interface) are not on the same network segment, a problem will occur. For instance, the configuration of the printer (with a LAN interface) cannot be set up from the Quick Setup or Printserver Version Up Tool utility.

Ensure that the printer (with a LAN interface) and the computer are connected on the same network segment before using these utilities.

6- 5

Image 53

Toshiba B-SX600 manual Printing from Your Computer

Contents

SX600 Series Vorsicht CE Compliance for EU only Meanings of Each Symbol Safety Summary Precautions Table of Contents Test Print Specifications Introduction Product Overview CD-ROM Accessories Front View Part Names and Functions AC Power Inlet Fanfold Paper Slot USB Interface ConnectorRear View Model with a USB interface Ventilation Slot Rear View Model with a LAN interface LAN Interface Connector Media End Sensor Reflective Media Sensor Media Holder InteriorMedia Roll Damper Platen Media Roll Guide Media Guide Print Head Upper Unit Handle Ribbon Tensioner Upper Unit Unlock Lever Upper Unit Menu key Cancel keyOperation Panel Cut position Cutter Unit Precautions when using the Cutter Unit Part names Peel-off Unit Supplemental Remarks Precautions when using the Peel-off Unit Removing the Protective Materials Printer SetupPrecautions Printer Setup Printer Setup 40 C Installation Location Example of US Type Connecting the Power Cord Connecting the Printer with a USB Interface to Your Computer Connecting the Printer with a LAN Interface to Your Computer Media and Ribbon Supply SpecificationsStrip mode Cut mode Die-cut label Notched media Label with black marks Guaranteed Print Area Storage of Media and Ribbons When you purchase media and ribbonsUnacceptable Media and Ribbons Preprinted Media Media and Ribbon Loading the Ribbon Precaution Release button Gently squeeze the metal. plate Precautions Loading the Media How to Load the Media Loading the Media Low Supplemental Remarks Please read .1 How to Load the Media first How to Load the Media for the Model with the Peel-off Unit Precautions Loading the Media Loading the Media How to Load a Narrow Label Stock How to Reload the Media when the Upper Unit is Lifted How to Load Fanfold Paper Print Test from Printer Driver Printing from Your Computer Printing from Your Computer Printing from Your Computer Precautions when Using the Model with a LAN Interface Printing from Your Computer Fixed Length feed mode Media Feed ModeStrict feed mode Easy feed mode Printer Operation Printer Operation Tear-off Alignment is performed Alignment Alignment when Precise print mode is selected Alignment when Paper saving mode is selected Media Calibration Alignment when Fixed Length feed mode is selected How to perform a media calibration Printer Operation Printer Operation Operation Panel Operation Panel Messages Displayed on the Operation Panel Display when Pause is shown Display when Printing is shown Display in Low Power Mode Error messages in the event of End of paper → See .4 Menu Options Printer Operation using the Operation PanelOperation Operational procedures Information Menu Options Trip Title Description Test print menu Reprint Error Page menuClear Trip Meter menu Conditions Low Power min Beep Volume How to Cancel a Print Job Operation Panel Print Test Pattern How to Perform a Print TestTest Print Removing Jammed Media from the Cutter Unit Removing Jammed Media Removing Jammed Media from the Peel-off Unit Daily Maintenance Cleaning the Media Sensor Cleaning the Platen Cleaning the Ribbon Guide Bar Cleaning the Ribbon Separation Plate Cleaning the Print Head Cleaning the Peel-off Unit Problems at Start-up of the Printer TroubleshootingProblems while Printing Printing does not start ⇒8.5 How to Cancel a Print Job ⇒2.4 or 2.5 Connecting the Printer to YourComputer ⇒ 3.7 Unacceptable Media and Ribbons Loaded ribbon is torn or ejected with the media ⇒ 11.3 Cleaning the Ribbon Separation PlateBlank page label is ejected Printed text is blurred Print FailureAn entire or a part of printout is light Printouts have streaky smudges or fine lines ⇒ 2.2 Installation Location ⇒ 7.4 Media Calibration ⇒ 7.1 Media Feed ModePrint position gradually misaligns ⇒ Help on the Printing Preferences ⇒ 8.5 How to Cancel a Print Job ⇒ 2.5 Connecting the Printer to Your Computer Problems in the Network Model with a LAN Interface Error messages and remedial measures ⇒ 1.5.2 Precaution when using the Peel-off Unit How to Load the Media⇒ 1.4.2 Precautions when using the Cutter Unit Peeling failed Action Info.Error Error messages Possible causes Solutions Info. ErrorImage Info.Error Possible causes Solutions Bad thermal head Can I use an ink ribbon narrower than a label? Frequently Asked Questions FAQHow can I use the printer with the covers left open? Ribbon is torn apart during printing. What should I do? Peeling failure occurs more frequently than before Frequently Asked Questions FAQ Remarks Standard model Printer Model with a USB Interface SpecificationsSpecifications Http Printer Model with a LAN Interface Snmp Simple Network Management Protocol Specifications Cutter Unit When purchasing the power cord Power CordPage EO1-33085