Toshiba G9000 operation manual 90.6 x 32.7 x 4255 207 79,147, 781 939 1400 a 500 kcmil

Installation Planning Guide for 750kVA UPS

Standard System: 480V Input, 480V Output

General Mechanical Information

Dimensions	Weight	Floor	Approximate Full-Load	Mechanical Clearance (Inches)from UPS
			Heat Rejection	for Ventilation and Maintenance Access
(W x D x H)		Loading
Inches	Lbs.	Lbs./ft. 2	Btu/Hr	Top	Front	Bottom	Sides**	Back
90.6” x 32.7” x 80.7”*	4255	207	79,147	20”	40”	0”	0”	0”

*Height includes removable fan housing – Frame height is 78.7”.

**0” clearance for peripheral equipment, 1” clearance for walls.

Primary AC Input (480V 3-Phase / 3-Wire)

Maximum Input Power Demand			Suggested External	External Feeder Wire Size: Min. – Max. Per Phase
Normal Mode (Recharge Mode)			Overcurrent Protection
kVA	PF	Amps	Amps	AWG or kcmil at 75º C Temp. Rating
781 (875)	>0.99	939 (1052)	1400 A	(4) x 500 kcmil

Alternate (Bypass) AC Input (480V 3-Phase / 3-Wire)

Maximum Input Power Demand			Suggested External	External Feeder Wire Size:
			Overcurrent Protection	Min. – Max. Per Phase
kVA	PF	Amps (Max.)	Amps	AWG or kcmil at 75º C Temp. Rating
750	1.0	902	1200 A	(4) x350 kcmil – (4) x 400 kcmil

Battery Input (480VDC Nominal)

Battery Capacity Required		Discharge at Full	Suggested External	External Feeder Wire Size:
for Full Load Output		Load	Overcurrent Protection
kWB		Amps DC	Amps	AWG or kcmil at 75º C Temp. Rating
776 @ 1.0 PF	1935		2000 AT	(6) x 400 kcmil – (6) x 500 kcmil

* Contact factory rep for alternate configurations.

AC Output (480V 3-Phase / 3-Wire)

Rated Output Power			Suggested External	External Feeder Wire Size:
			Overcurrent Protection	Min. – Max. Per Phase
kVA	PF	Amps	Amps	AWG or kcmil at 75º C Temp. Rating
750	1.0	902	1200 A	(4) x350 kcmil – (4) x 400 kcmil

Important Notes:

1.Maximum input current is limited to 106% of the full-load input current.

2.Output load conductors are to be installed in separate conduit from input conductors.

3.Control wires and power wires are to be installed in separate conduits.

4.Recommended AC input and output overcurrent protection based on continuous full load current per NEC.

5.Wiring shall comply with all applicable national and local electrical codes.

6.Grounding conductors to be sized per NEC Article 250-122. Neutral conductors to be sized per NEC Article 310.15.

-Primary AC Input: 3φ, 3-wire + ground.

-Alternate AC Input: 3φ, 3-wire + ground.

-AC Output: 3φ, 3-wire + ground.

- DC Input: 2-wire (Positive/Negative) + ground.

7.Nominal battery voltage based on the use of VRLA type batteries (2.0 volts/cell nominal).

8.Maximum battery discharge current based on lowest permissible discharge voltage of 1.67 VPC.

9.DC wires should be sized to allow not more than a 2-volt drop at maximum discharge current.

10.Weights do not include batteries or other auxiliary equipment external to the UPS.

11.Cable sizing calculations based on the following assumptions:

-Minimum size is smallest size based on ampacity at 30 °C.

-Maximum size cable is based on cable bend radius limitations at the UPS terminals.

-Not more than 3 current-carrying conductors installed in conduit in ambient temperature of 30 °C.

-Temperature rating of copper conductors/terminals: 75 °C.

-Reference: 2005 NEC Handbook, Table 310.16.

NOTE: Consult latest edition of applicable national and local codes for possible variations.

12.Ratings of wires and overcurrent devices are suggested minimums. Consult with a registered Professional Engineer within your local area for proper size selections.

TOSHIBA INTERNATIONAL CORPORATION

13131 West Little York Road

Houston, TX 77041

Telephone: (800) 231-1412

Fax: (713) 896-5212

Web Site: www.toshiba.com/ind

G9000 Installation and Operation Manual 91