While in use, the treadmill gathers dust that may cause problems in the operation of the equipment.
You should check the lubrication approximately after every 500 hours of use. The meter is equipped with a counter for measuring total values, thus allowing you to monitor your total training time on the treadmill. If there is any jerky movement of the belt, always check the lubrication level. To do this, let the treadmill come to a complete stop, then simply lift the running belt to feel the running deck; if the deck feels dry and there is very little evidence of lubricant on your hand, lubricate the running deck according to the following instructions:
1.Attach the nozzle to the lubricant container.
2.Let the treadmill come to a complete stop, and then lift the running belt.
3.Position nozzle between the belt and the board approximately 200 mm (8”) from the front of the treadmill.
4.Apply
5.The treadmill is instantly ready for use.
NOTE! Lubricate your treadmill only with
ALIGNING THE RUNNING BELT
Monitor belt tracking during exercise and make adjustments as needed. The belt should run in the center of the treadmill. Alignment is not usually needed, provided
•the treadmill is placed on an even, solid and horizontal surface and the belt is correctly tensioned
•the alignment of the belt is correct
It is, however, possible for the belt to be pushed to one side due to the user’s running style (e.g. more weight on one foot). The alignment of the belt is adjusted by turning the two bolts at the back of the treadmill.
Align the belt according to the following instructions:
1.Turn the power switch on and increase the treadmill’s speed to 5 km/h (3 mph).
2.If the belt drifts to the left, turn the left adjustment bolt ¼ turn clockwise and the right adjustment bolt 1/8 turn
3.If the belt remains centered the adjustment is correct. If not, continue to make small adjustments as above until the belt is correctly aligned. If the belt is allowed run across to one side for long periods of time the edges of the belt may be damaged and the treadmill may not continue to operate correctly. Any damage to the belt caused by the lack of necessary adjustment will not be covered by the warranty.
O W N E R ’ S M A N U A L • T 9 0
ADJUSTING THE BELT TENSION
The belt must be tensioned if it begins to slip on the rollers. In normal use, however, keep the belt as loose as possible! The belt tension is adjusted by turning the same screws as used for aligning the running belt. If turning the screws will not effect the belt tension, please contact your local Tunturi dealer.
1.Increase the treadmill’s speed to 5 km/h (3 mph).
2.Turn both adjustment screws an equal amount, ¼ turn clockwise.
3.Try to slow the belt down by holding onto the handrails and braking as you walk (as if you were walking downhill).
If the belt slips, turn another ¼ turn and repeat the test. When braking heavily the belt may slip. If the belt keeps slipping despite repeated adjustments, please contact your local Tunturi dealer.
MALFUNCTIONS
NOTE! Despite continuous quality control, defects and malfunctions caused by individual components may occur in the equipment. In most cases it’s unnecessary to take the whole device in for repair, as it’s usually sufficient to replace the defective part. Always give the model, serial number of your equipment and in case of malfunctions also conditions of use, nature of malfunction and any error code.
When you encounter unusual behavior from the treadmill, simply turn the power switch off, wait 1 minute and turn the power switch on to reset the treadmill. This should clear incidental errors and ready the treadmill for normal operation again. If after you have reset the treadmill by turning the power switch off and on again, and the treadmill is still not operational, contact your local Tunturi dealer for service.
If you require spare parts, always give the model, serial number of your equipment and the spare part number for the part you need. The spare part list is at the back of this manual. Use only spare parts mentioned in the spare part list.
ERROR CODES
The user interface will display information about operational faults.
SYSTEM CHECK FAILED - Possible motor controller fault. Turn the power switch off, wait 1 minute and turn the power switch on again. If treadmill recovers to normal operation, you may continue to use the treadmill. Otherwise, call the dealer for service.
SPEED SENSOR ERROR - Call the dealer for service.
MOTOR SPEED ERROR - Ensure correct usage of the treadmill. Do not push the belt with your feet. Turn the power switch off, wait 1 minute and turn the power switch on again. If treadmill recovers to normal operation, you may continue to use the treadmill. Otherwise, call the dealer for service.
GB
11
