Manuals / Wayne-Dalton / Household Appliance / Garage Door Opener

Wayne-Dalton 3790-Z installation instructions for TORQUEMASTER TORQUEMASTER PLUS

Models: 3790-Z 3790

1 52

Download 52 pages 22.06 Kb

Page 1

INSTALLATION INSTRUCTIONS AND OWNER’S MANUAL

INSTALLATION INSTRUCTIONS AND OWNER’S MANUAL

for TORQUEMASTER®/

TORQUEMASTER® PLUS

Models: 3790/3790-Z

Installation Instructions

and Owner’s Manual

USE OF THIS MANUAL

WHEN INSTALLING A NEW DOOR WITH AN IDRIVE®:

If you just ﬁ nished installing a new garage door along with an idrive® opener, then proceed with these instructions beginning with Step 14 on page 21. If you were referred to these instructions as part of a new door installation, then proceed with these instructions beginning with Step 1 on page 7.

IMPORTANT NOTICE!

To avoid possible injury, read the enclosed instructions carefully before installing/operating this garage door opener. Pay close attention to all warnings and notes. This manual MUST be attached to the wall in close proximity to the garage door opener.

WARNING PHOTOELECTRIC EYES ARE NOT REQUIRED

ON WAYNE-DALTON SERIES 9000 AND MODEL 5120 AND 5140 DOORS. ALL OTHER DOORS, WHICH DO NOT HAVE PINCH-RESISTANT SECTION JOINTS, REQUIRE PHOTOELECTRIC EYES TO PRE- VENT POSSIBLE SEVERE OR FATAL INJURY.

		® technologyhome
	-Wave				your
Z			network
			for
Integrated	Ready
	control			models
		select
	On

GARAGE DOORS & OPENERS

Copyright 2008 Wayne-Dalton Corp. Part No. 334101 Rev 2 7/16/2008

Image 1

Wayne-Dalton installation instructions for TORQUEMASTER TORQUEMASTER PLUS, Models 3790/3790-Z, Use Of This Manual

Contents

for TORQUEMASTER TORQUEMASTER PLUS Installation Instructions and Owner’s ManualModels 3790/3790-Z USE OF THIS MANUALPackage Contents PRIOR TO TORQUEMASTER IDRIVE INSTALLATION PRE-INSTALLATIONINSPECTION OF YOUR GARAGE DOORWHEN INSTALLING A NEW DOOR WITH AN IDRIVE TORQUEMASTER PLUSPre-Installation PRE-INSTALLATIONINSPECTIONInspection Tools Needed System RequirementsPAGES 31, 32 AND IMPORTANT SAFETY INSTRUCTIONSTable of Contents RETRO-FITTORQUEMASTER Retro-FitTorqueMaster PlusBefore AfterCenter Bracket & Cable Drum ROTATE WHEN REMOVING THE ENDCAUTION: THE WINDING SHAFT MAY to the right side of the torque tubeRetro-FitInstallation Retro-FitTorqueMasterCenter Bracket & Cable Drum End Bracket RemovalRemoval Vertical Track Height Adjustment Re-InstallIf Necessary9100 Top Bracket 8000/8100/8200 TrackTop Roller Adjustment Adjustment If Required8000/8100/8200 Track Horizontal Track HeightInstallation INSTALLATIONAssembling Opener IDRIVEFORTORQUEMASTERCable Drums spring tube assemblyNOTE: If you have a Torquemaster with Step 2 on page 10. If you have aINSTALLATION IDRIVEEnd Brackets Installation TorqueMaster InstallationCable Drum/ Drive Gear IDRIVE using 2 5/16” x 1-5/8lag screwsbracket does not have a hole for the align the hex of the counter cam withAttaching Opener To 4Positioning Support BracketSupport Bracket pliers 6Attaching Disconnect Cablebracket TorquemasterMounting Disconnect Tools Needed Pencil Tape Measure Power DrillHandle Bracket 1/8 Drill Bit 7/16” Socket Driver8Attaching Disconnect Handle teeth are engaged before installingDisconnect Handle Usage clockwise until motor is fully downTorquemaster Cable Adjustmentsfor Spring Winding Securing DoorWinding Springs TorqueMaster PlusWinding Springs Continued Drum Wrap InstallationUn-snapthe drum wrap hinged latch and rotate down Repeat for the left hand sideSetting Spring Tension TorqueMasterMounting Wall Station Drum Wrap InstallationMounting Wall Station Installing BatteryInstalling the Light Fixture PRE-OPERATIONIf Included Power Cord Connecting OpenerAttaching Diffuser If IncludedPRE-OPERATION Safety Sensors InstallationSensor Wire Installation PRE-OPERATION Safety Sensor Alignmentand Checking for Obstructions Programming Light Fixture on when program button is pushedIf Included Profile Routine Standard Upper Limitadjustment screw Adjusting Detenta detent pin adjustment may need to preset at the factory via the detent pinLock Arm Installation Adjusting Detent ContinuedPRE-OPERATION reverse when it contacts a 1-1/2”highobject or a 2 x 4 board laid flat on the Place a 2 x 4 board flat on the garagesensors, one foot from the left side of Starting with the door fully open, placeand then reverse to fully open position Repeat this test with the 6” high objectIMPORTANT SAFETY INSTRUCTIONS OPERATIONTO REDUCE THE RISK OF SEVERE INJURY OR DEATH 8.SAVE THESE INSTRUCTIONSOperating the Wireless Wall Station Programming/Training HomeLink Unit OPERATIONProgramming/Training HomeLink Unit OPERATION Customizing the SettingsNORMAL DOOR LOCKMaintenance h.Reconnect Power Power Connection — Permanent Wiring OptionOPERATION f.Confirm pot nut position* shown belowHere r PressoWeak or dead Transmitter battery No power to the OpenerWeak or dead Wall Station battery No power to the OpenerInstall new bulb 75W Max Faulty light bulbNo power to receptacle Re-installHandle per instructions in Stepidrive for TorqueMaster and TorqueMaster Plus Lifetime Limited WarrantyPlease Do Not Return This Product To The Store Call Us Toll-Free:888Cut-OutTemplate to Aid Installation Pre-drill5/64” pilot holeFCC and IC Statement Patent InformationModels: 3790/3790-Z FCC Regulatory Information