Attaching Disconnect Cable, Pliers, Bracket

6Attaching Disconnect Cable

	Tools Needed:	Attach the loose disconnect cable (located in
	Step Ladder	opener hardware bag) to the opener with the
	Step Ladder	“S” hook. Close both ends of the “S” hook
	Pliers	“S” hook. Close both ends of the “S” hook
	Pliers	with pliers, to lock assembly together with
		pliers.
		Thread the disconnect cable (behind the
		counterbalance cable) through the hole in
		the right hand end bracket, and remove all
		slack between opener and right end
		bracket.

Close “S” Hook

Torquemaster®	Right Side of
	End Bracket
	End Bracket

		Hole in
		End Bracket

S-Hook

Disconnect

Cable

Hole in Right

End Bracket

®INSTALLATION TORQUEMASTER

Torquemaster® Plus

Hole in

End Bracket

Right Side of End

S-HookBracket

Disconnect

Cable

Hole in Right

End Bracket

®FOR IDRIVE

Please Do Not Return This Product To The Store. Call Us Directly! Our Trained Technicians Will Answer Your Questions and/or Ship Any Parts You May Need. 13 You can reach us Toll Free at 1-888-827-3667 for Consumer Assistance or online at www.wayne-dalton.com

Page 19

Image 19

Wayne-Dalton 3790-Z Attaching Disconnect Cable, Pliers, Bracket, Slack between opener and right end

Contents

For Copyright 2008 Wayne-Dalton Corp. Part No Rev 2 7/16/2008Your Network Package Contents Look for this symbol When Installing a NEW Door with AN Idrive Inspection Pre-InstallationEyes to Prevent Possible Severe or Fatal Injury Door Models below require the use of photo eyes System RequirementsTools Needed WAYNE-DALTON Track Radius Photoelectric LOW Head Deﬁnition of key words used in this manual Table of Contents Spring Tension Removal Retro-Fit InstallationDrum Wrap & End Bracket Removal Center Bracket & Cable Drum End Bracket RemovalBracket and Gear IMPORTANT! Right and Left Hand is Retro-Fit InstallationPowerful Spring Releasing ITS Even Fatal Injury Removal End Bracket Removal 8000/8100/8200 Track Re-Install If NecessaryVertical Track Height Adjustment Top Bracket Failure to RE-ATTACH Horizontal Top Roller AdjustmentTracks to the Support Before Opening Door can Cause Door Assembling Opener Installation Cable Drums Repeat for other end bracket Tools Needed Power Drill Socket Driver Wrench Step LadderSecure end bracket to the flag angle using End Brackets Cable Drum/ Drive Gear Installation Brackets End Bracket InstallationCounterbalance Springs Attaching Opener To Positioning Support BracketSupport Bracket Slack between opener and right end Attaching Disconnect CablePliers Bracket 6ft Pilot drill lag screw location using 1/8 drill bitMounting Disconnect Handle Bracket Disconnect Handle Usage Attaching Disconnect Handle Springs Cable Adjustments For Spring Winding Securing DoorTools Needed Vice Clamps Hands Winding Springs IMPORTANT! do not Overwind Springs Drum Wrap InstallationRecommended Spring Turns Tools Needed SCREWS. for Detailed Information on Setting Spring TensionProblems IMPORTANT! do not Overwind Mounting Wall Station Drum Wrap Installation Installing Battery If Included Installing the Light FixtureDisconnect Power to Install hole plug into the screw hole in the light fixture If Included Connecting OpenerPower Cord Attaching Diffuser Sensor Unit For Proper Alignment View of the Opener from the Front Sensor Wire Installation Checking for Obstructions Safety Sensor Alignment On and remain on for 30 seconds On when program button is pushedProgramming Light Fixture Profile Routine Standard Upper Limit Profile Routine Custom Upper Limit Adjusting DetentWork Properly Tools Needed Tape Measure Step Ladder Lock Arm InstallationConfirm adjustment Turn increments Contact Obstruction Test Lock Arm Installation Fatal Injury MAY Result Testing the Safety Sensors Never GO Under a STOPPED, Partially Open Door Read and Follow ALL InstructionsDoor activation Emergency Disconnect Operating the Wireless Wall Station Teaching HomeLink to the idrive opener Programming/Training HomeLink Unit Programming/Training HomeLink Unit For more profile options go to page 28 Customizing the SettingsCustom pet position Multi-Door Programming Maintenance Potentiometer Gear Power Connection Permanent Wiring OptionReconnect Power Confirm pot nut position* shown below Light Button Large Button Stations or Transmitters to OpenerProgramming Wireless WallHandle In Manual Door Operated Position Motor Up Position Red Program Button Symptom Probable Cause Corrective Action Troubleshooting Lock Arm Troubleshooting Dalton dealer or distributor Thank you for your purchase Cut-Out Template to Aid InstallationPre-drill 3/32 pilot hole Pre-drill 5/64 pilot hole Models 3790/3790-Z Patent Information

Wayne-Dalton 3790-Z installation instructions Attaching Disconnect Cable, Pliers, Bracket

Models: 3790-Z 3790

6Attaching Disconnect Cable

pliers.

slack between opener and right end

bracket.

Torquemaster®

End Bracket