Manuals / Wayne-Dalton / Household Appliance / Garage Door Opener

Wayne-Dalton 3790-Z installation instructions

Models: 3790-Z 3790

1 52

Download 52 pages 22.06 Kb

Page 52

Image 52

Page 52

Image 52

Wayne-Dalton 3790-Z installation instructions

Contents

Installation Instructions and Owner’s Manual for TORQUEMASTER TORQUEMASTER PLUSModels 3790/3790-Z USE OF THIS MANUALPackage Contents PRE-INSTALLATIONINSPECTION OF YOUR GARAGE DOOR PRIOR TO TORQUEMASTER IDRIVE INSTALLATIONWHEN INSTALLING A NEW DOOR WITH AN IDRIVE TORQUEMASTER PLUSPre-Installation PRE-INSTALLATIONINSPECTIONInspection System Requirements Tools NeededPAGES 31, 32 AND IMPORTANT SAFETY INSTRUCTIONSTable of Contents Retro-FitTorqueMaster Plus RETRO-FITTORQUEMASTERBefore AfterROTATE WHEN REMOVING THE END Center Bracket & Cable DrumCAUTION: THE WINDING SHAFT MAY to the right side of the torque tubeRetro-FitTorqueMaster Retro-FitInstallationCenter Bracket & Cable Drum End Bracket RemovalRemoval Re-InstallIf Necessary Vertical Track Height Adjustment9100 Top Bracket 8000/8100/8200 TrackAdjustment If Required Top Roller Adjustment8000/8100/8200 Track Horizontal Track HeightINSTALLATION InstallationAssembling Opener IDRIVEFORTORQUEMASTERspring tube assembly Cable DrumsNOTE: If you have a Torquemaster with Step 2 on page 10. If you have aINSTALLATION IDRIVEEnd Brackets Installation TorqueMaster InstallationCable Drum/ Drive Gear using 2 5/16” x 1-5/8lag screws IDRIVEbracket does not have a hole for the align the hex of the counter cam withAttaching Opener To 4Positioning Support BracketSupport Bracket 6Attaching Disconnect Cable pliersbracket TorquemasterTools Needed Pencil Tape Measure Power Drill Mounting DisconnectHandle Bracket 1/8 Drill Bit 7/16” Socket Driverteeth are engaged before installing 8Attaching Disconnect HandleDisconnect Handle Usage clockwise until motor is fully downCable Adjustments TorquemasterSecuring Door for Spring WindingTorqueMaster Plus Winding SpringsDrum Wrap Installation Winding Springs ContinuedUn-snapthe drum wrap hinged latch and rotate down Repeat for the left hand sideTorqueMaster Setting Spring TensionDrum Wrap Installation Mounting Wall StationInstalling Battery Mounting Wall StationInstalling the Light Fixture PRE-OPERATIONIf Included Connecting Opener Power CordAttaching Diffuser If IncludedSafety Sensors Installation PRE-OPERATIONSensor Wire Installation PRE-OPERATION Safety Sensor Alignmentand Checking for Obstructions on when program button is pushed Programming Light FixtureIf Included Profile Routine Standard Upper LimitAdjusting Detent adjustment screwa detent pin adjustment may need to preset at the factory via the detent pinAdjusting Detent Continued Lock Arm Installationreverse when it contacts a 1-1/2”high PRE-OPERATIONobject or a 2 x 4 board laid flat on the Place a 2 x 4 board flat on the garageStarting with the door fully open, place sensors, one foot from the left side ofand then reverse to fully open position Repeat this test with the 6” high objectOPERATION IMPORTANT SAFETY INSTRUCTIONSTO REDUCE THE RISK OF SEVERE INJURY OR DEATH 8.SAVE THESE INSTRUCTIONSOperating the Wireless Wall Station OPERATION Programming/Training HomeLink UnitProgramming/Training HomeLink Unit Customizing the Settings OPERATIONNORMAL DOOR LOCKMaintenance Power Connection — Permanent Wiring Option h.Reconnect PowerOPERATION f.Confirm pot nut position* shown belowPresso Here rNo power to the Opener Weak or dead Transmitter batteryWeak or dead Wall Station battery No power to the OpenerFaulty light bulb Install new bulb 75W MaxNo power to receptacle Re-installHandle per instructions in StepLifetime Limited Warranty idrive for TorqueMaster and TorqueMaster PlusCall Us Toll-Free:888 Please Do Not Return This Product To The StoreCut-OutTemplate to Aid Installation Pre-drill5/64” pilot holePatent Information FCC and IC StatementModels: 3790/3790-Z FCC Regulatory Information