Manuals / Wayne-Dalton / Household Appliance / Garage Door Opener

Wayne-Dalton 3790-Z installation instructions System Requirements, Tools Needed

Models: 3790-Z 3790

1 52

Download 52 pages 22.06 Kb

Page 5

System Requirements

System Requirements

CAUTION TO REDUCE THE RISK OF INJURY, USE THIS OPENER ONLY WITH THE FOLLOWING DOOR MODELS:

	WAYNE-DALTON	WAYNE-DALTON	TRACK (RADIUS)	PHOTOELECTRIC	LOW HEAD
	DOOR MODEL	SPRING SYSTEM		SAFETY SENSORS	ROOM KIT


	9000 SERIES,	Torquemaster®	10",12",14",15"	Not Required	Not Required
	5120 & 5140	Torquemaster® Plus

	9000 SERIES,	Torquemaster®	6" Low Head Room	Not Required	P/N 302883
	5120 & 5140	Torquemaster® Plus			Required

Door Models below require the use of photo eyes.

	8000 SERIES or			Torquemaster®	10",12",14",15"	P/N’s 252118 or	Not Required
	other doors			Torquemaster® Plus	10",12",14",15"	301674 Required	Not Required
	other doors			Torquemaster® Plus		301674 Required
	8000 SERIES or			Torquemaster®	6" Low Head Room	P/N’s 252118 or	P/N 302883
	other doors			Torquemaster® Plus	6" Low Head Room	301674 Required	Required
	other doors			Torquemaster® Plus		301674 Required	Required
			Tools Needed

Power Drill	Ratchet Wrench	Pliers/Wire	3/32” Drill Bit	3/16” Drill Bit
		Cutters

Phillips Head	7/16” Socket	Pencil	7/16” Wrench	1/8” Drill Bit	5/64” Drill Bit
Screwdriver

Flat Tip	7/16” Socket Driver	Level	Needle Nose Pliers
Screwdriver

Tape Measure

Safety Glasses

Locking Pliers

Vice Clamps

Step Ladder

Please Do Not Return This Product To The Store. Call Us Directly! Our Trained Technicians Will Answer Your Questions and/or Ship Any Parts You May Need. IV You can reach us Toll Free at 1-888-827-3667 for Consumer Assistance or online at www.wayne-dalton.com

Image 5

Wayne-Dalton 3790-Z installation instructions System Requirements, Tools Needed

Contents

for TORQUEMASTER TORQUEMASTER PLUS Installation Instructions and Owner’s ManualModels 3790/3790-Z USE OF THIS MANUALPackage Contents PRIOR TO TORQUEMASTER IDRIVE INSTALLATION PRE-INSTALLATIONINSPECTION OF YOUR GARAGE DOORWHEN INSTALLING A NEW DOOR WITH AN IDRIVE TORQUEMASTER PLUSInspection PRE-INSTALLATIONINSPECTIONPre-Installation Tools Needed System RequirementsTable of Contents IMPORTANT SAFETY INSTRUCTIONSPAGES 31, 32 AND RETRO-FITTORQUEMASTER Retro-FitTorqueMaster PlusBefore AfterCenter Bracket & Cable Drum ROTATE WHEN REMOVING THE ENDCAUTION: THE WINDING SHAFT MAY to the right side of the torque tubeRetro-FitInstallation Retro-FitTorqueMasterRemoval End Bracket RemovalCenter Bracket & Cable Drum Vertical Track Height Adjustment Re-InstallIf Necessary9100 Top Bracket 8000/8100/8200 TrackTop Roller Adjustment Adjustment If Required8000/8100/8200 Track Horizontal Track HeightInstallation INSTALLATIONAssembling Opener IDRIVEFORTORQUEMASTERCable Drums spring tube assemblyNOTE: If you have a Torquemaster with Step 2 on page 10. If you have aEnd Brackets IDRIVEINSTALLATION Cable Drum/ Drive Gear TorqueMaster InstallationInstallation IDRIVE using 2 5/16” x 1-5/8lag screwsbracket does not have a hole for the align the hex of the counter cam withSupport Bracket 4Positioning Support BracketAttaching Opener To pliers 6Attaching Disconnect Cablebracket TorquemasterMounting Disconnect Tools Needed Pencil Tape Measure Power DrillHandle Bracket 1/8 Drill Bit 7/16” Socket Driver8Attaching Disconnect Handle teeth are engaged before installingDisconnect Handle Usage clockwise until motor is fully downTorquemaster Cable Adjustmentsfor Spring Winding Securing DoorWinding Springs TorqueMaster PlusWinding Springs Continued Drum Wrap InstallationUn-snapthe drum wrap hinged latch and rotate down Repeat for the left hand sideSetting Spring Tension TorqueMasterMounting Wall Station Drum Wrap InstallationMounting Wall Station Installing BatteryIf Included PRE-OPERATIONInstalling the Light Fixture Power Cord Connecting OpenerAttaching Diffuser If IncludedPRE-OPERATION Safety Sensors InstallationSensor Wire Installation and Checking for Obstructions Safety Sensor AlignmentPRE-OPERATION Programming Light Fixture on when program button is pushedIf Included Profile Routine Standard Upper Limitadjustment screw Adjusting Detenta detent pin adjustment may need to preset at the factory via the detent pinLock Arm Installation Adjusting Detent ContinuedPRE-OPERATION reverse when it contacts a 1-1/2”highobject or a 2 x 4 board laid flat on the Place a 2 x 4 board flat on the garagesensors, one foot from the left side of Starting with the door fully open, placeand then reverse to fully open position Repeat this test with the 6” high objectIMPORTANT SAFETY INSTRUCTIONS OPERATIONTO REDUCE THE RISK OF SEVERE INJURY OR DEATH 8.SAVE THESE INSTRUCTIONSOperating the Wireless Wall Station Programming/Training HomeLink Unit OPERATIONProgramming/Training HomeLink Unit OPERATION Customizing the SettingsNORMAL DOOR LOCKMaintenance h.Reconnect Power Power Connection — Permanent Wiring OptionOPERATION f.Confirm pot nut position* shown belowHere r PressoWeak or dead Transmitter battery No power to the OpenerWeak or dead Wall Station battery No power to the OpenerInstall new bulb 75W Max Faulty light bulbNo power to receptacle Re-installHandle per instructions in Stepidrive for TorqueMaster and TorqueMaster Plus Lifetime Limited WarrantyPlease Do Not Return This Product To The Store Call Us Toll-Free:888Cut-OutTemplate to Aid Installation Pre-drill5/64” pilot holeFCC and IC Statement Patent InformationModels: 3790/3790-Z FCC Regulatory Information