19 |
|
|
| Safety Sensors Installation | ||
8000 Series Doors (Required) (Not Required | ||||||
| ||||||
|
|
| On 9000, 5120 & 5140 Series Doors) | |||
|
|
|
|
|
| |
Tools Needed: |
|
| NOTE (Per UL): Safety sensors are required | |||
|
| if opener is installed on a | ||||
Tape Measure |
|
| ||||
|
| door. If your door is a | ||||
Power Drill |
|
| series, 5120 or 5140 pinch resistant door, | |||
|
| skip this step and proceed with Step 22. | ||||
3/16" Bit |
|
| ||||
|
|
|
|
| ||
|
|
| WARNING |
| ||
7/16” Socket |
|
|
|
| ||
|
| PHOTOELECTRIC EYES ARE NOT RE- | ||||
Driver |
|
| ||||
|
| QUIRED ON | ||||
7/16” Wrench |
|
| AND MODEL 5120 AND 5140 DOORS. | |||
|
| ALL OTHER DOORS, WHICH DO NOT HAVE | ||||
|
|
| ||||
Pencil |
|
| ||||
|
| QUIRE PHOTOELECTRIC EYES TO PREVENT | ||||
|
|
| ||||
|
|
| POSSIBLE SEVERE OR FATAL INJURY. | |||
|
|
| a. Select and mark with a pencil, a suitable | |||
|
|
| mounting location no more than | |||
|
|
| 5 inches above the floor to the center line | |||
|
|
| of wall mounting bracket. The safety | |||
|
|
| sensors should be mounted as close to the | |||
|
|
| door track or inside edge of the door as | |||
|
|
| possible to offer maximum entrapment | |||
|
|
| protection. It is very important that both | |||
|
|
| wall mounting brackets be mounted at the | |||
|
|
| same height for proper alignment. | |||
|
|
| IMPORTANT! BOTH WALL BRACKETS | |||
|
|
| MUST BE MOUNTED AT THE SAME HEIGHT | |||
|
|
| FOR PROPER ALIGNMENT. | |||
|
|
| b. Drill pilot holes, using a 3/16” drill bit. | |||
|
|
| Using two 5/16” x | |||
|
|
| permanently mount the wall mounting | |||
|
|
| brackets to both door jambs. In some | |||
|
|
| installations it may be necessary to attach a | |||
|
|
| wooden spacer to the wall to achieve the | |||
|
|
| required alignment. | |||
|
|
| Attach the “U” brackets to the wall | |||
|
|
| mounting brackets with | |||
|
|
| carriage bolts, washers and nuts. | |||
|
|
| Insert the bolts from the inside of the | |||
|
|
| “U” bracket and | |||
|
|
| c. Attach the sending and receiving safety | |||
|
|
| sensors to the “U” brackets by inserting all | |||
|
|
| three tabs into the respective holes. | |||
|
|
| IMPORTANT! IDENTIFY WHICH SIDE OF THE | |||
|
|
| GARAGE DOOR IS EXPOSED TO THE MOST | |||
|
|
| SUNLIGHT. MOUNT THE SENDING UNIT (UNIT | |||
|
|
| WITHOUT LED) ON THE SIDE WHICH IS | |||
|
|
| EXPOSED TO THE MOST SUN. SUNLIGHT MAY | |||
|
|
| AFFECT THE SAFETY SENSORS, AND THIS | |||
|
|
| POSITIONING WILL HELP REDUCE THE | |||
|
|
| ADVERSE EFFECT SUNLIGHT MAY HAVE ON | |||
|
|
| THE SENSOR UNIT. | |||
|
|
|
|
|
|
Wall Mounting
Bracket
5”
a |
| |
b | Door Jam | |
| ||
Wall Mounting | 5/16 x | |
Bracket | ||
Lag Screw | ||
| ||
Nut |
|
Washer
Carriage Bolt
c
LED
Receiving
Unit
Please Do Not Return This Product To The Store. Call Us Directly! Our Trained Technicians Will Answer Your Questions and/or Ship Any Parts You May Need. 25 You can reach us Toll Free at