Customizing the Settings (Continued)

 

Erasing Remote Controls:

CAUTION: MANUALLY DISCONNECT THE DOOR FROM OPENER USING THE EMERGENCY DISCONNECT HANDLE PRIOR TO ERASING REMOTE CONTROLS.

To clear programming of all remote control devices, press and hold the opener’s red program button for approximately 10 seconds. When the opener beeps 3 times, all remote controls are erased.

Multi Opener Light Control:

A single light fixture can be controlled by up to 6 openers. Follow the procedure outlined on Step 23 to program additional openers.

Erasing Light Fixtures:

To clear programming of all openers from a light fixture, press and hold the light fixture program button for approximately 10 seconds. When the light fixture lamp and LED flash 3 times, all openers are erased.

Z-Wave

 

 

Controls

 

enabled

 

 

 

what’s

Learn

S1 S2

 

 

 

OPENING

S3

S4

 

 

 

Delete

 

 

 

 

your world?

 

 

 

 

 

®

 

 

 

 

 

With Z-Wave

 

 

 

 

 

technology you can

 

 

 

 

 

control your lights,

 

 

 

 

 

thermostat andstart

 

Red

 

 

 

your morning coffee,

 

 

 

 

tallwiththe single

 

 

 

 

ouch of a button.

Program

 

 

Find out more:

 

 

www.Wayne-

 

 

Dalton.com/access

 

 

 

Button

 

 

 

Program Button

 

 

 

 

 

 

Maintenance

 

 

 

 

 

Monthly Maintenance:

Battery replacement for Wall Station:

1. Lubricate hinges and rollers of garage door.

Remove the battery cover completely (right-hand side of wall

2. Inspect the door for loose fasteners, worn or frayed

station) by disengaging the battery cover’s lower clip. Install two

AAA batteries into the wall station observing the polarity, (+) and (-),

counterbalance cables and the presences of legible safety labels/

of both batteries. After a few seconds, the red LED will begin to

tags. Have repairs made by a qualified service person.

blink every three seconds. If it is desired to slow the red LED blink

Contact customer assistance for safety labels/ tags.

rate refer to the wall station operation section on page 34 “Backlit

 

 

3. With door fully closed, move the emergency disconnect to the

LED Light”. Re-install the battery cover by first inserting its top into

manual door operated position and manually operate door. If the

the wall station then inserting and securing its bottom.

door feels unbalanced or binds, have a qualified service person

Note: Use only 2 AAA batteries.

make necessary adjustments or repairs to the door.

 

4. Perform the contact/obstruction tests. See Steps 28 and 29 for

Battery replacement for Transmitter:

 

the contact/obstruction test instructions. If Door/Opener fails

Insert a coin in the coin slot of the transmitter and twist coin to

Contact/Obstruction test run profile routine Steps 24 or 25

access the dead battery. Replace the battery, being careful to match

making sure door is completely closed prior to activation. If

the positive (+) symbols on the circuit boards with the battery.

opener still fails, have a qualified service person make

Note: Use (1) CR2016 or equivalent battery.

adjustments/repairs or this could result in severe or fatal injury.

 

5. Failure of Door/Opener to respond to transmitter or wall station

Note: Dispose of dead battery properly.

 

may be due to a weak or dead battery. Replace the battery.

 

 

 

 

38Please Do Not Return This Product To The Store. Call Us Directly! Our Trained Technicians Will Answer Your Questions and/or Ship Any Parts You May Need.

You can reach us Toll Free at 1-888-827-3667 for Consumer Assistance or online at www.wayne-dalton.com

Page 44
Image 44
Wayne-Dalton 3790-Z installation instructions Maintenance