End Bracket Installation, Brackets | Wayne-Dalton 3790-Z specification

3End Bracket Installation

	Tools Needed:	IMPORTANT! WARNING TAGS MUST BE
	Power Drill	SECURELY ATTACHED TO BOTH END
	Power Drill	BRACKETS.
	3/32” Drill Bit	BRACKETS.
	3/32” Drill Bit	Slide the right hand end bracket over
	7/16”	Slide the right hand end bracket over
	7/16”	the drive gear. Replace #10 phillips head
	Socket Driver	screw that was removed in Step R3. Secure
	Phillips Head	end bracket and the flagangle to the jamb
	Screwdriver	using (2) 5/16” x 1-5/8" lag screws.
	Step Ladder	NOTE: Older end brackets may not have
		a hole needed for the opener’s emergency
		disconnect cable. If the right hand end
		bracket does not have a hole for the
		disconnect cable, drill a 3/32" (3mm) hole
		as shown prior to installing the end bracket.
		Install the right side counter gear, with
		the missing tooth toward the outside and
		away from the end bracket. Press the
		counter gear onto the end bracket until
		snaps engage.
		Select the right hand counter cover and
		align the hex of the counter cam with
		the end of the winding shaft. Also, align the
		“0” on the counter cover with the raised rib
		on the end bracket. Press the counter cover
		on the end bracket. Press the counter cover
		against the counter gear until it locks into
		place.
		Repeat for left hand side for double
		spring applications.
		NOTE: No drive gear, counter gear or
		counter cover is required on left hand side
		for single spring applications. Only an end
		bracket is needed.
		IMPORTANT! AT THIS TIME DO NOT WIND
		COUNTERBALANCE SPRINGS!
		After completing this step, continue with
		Step 4 on page 12.

	End Bracket	Warning
		Tag
5/16 x 1-5/8”
Lag Screws
		#10 Phillips
		Head
		Screw
		Flagangle
		1/4”
1/8”		3/32” Hole
		3/32” Hole
			®INSTALLATION
	Winding		TORQUEMASTER
	Shaft Inside End
	Bracket	Counter
		Counter
		Gear
		Missing
		Missing	FOR
		Tooth
		Counter
		Cover	®
			IDRIVE
Raised Rib
	Hex of the
	Counter Cam

Please Do Not Return This Product To The Store. Call Us Directly! Our Trained Technicians Will Answer Your Questions and/or Ship Any Parts You May Need. 11 You can reach us Toll Free at 1-888-827-3667 for Consumer Assistance or online at www.wayne-dalton.com

Image 17

Wayne-Dalton 3790-Z installation instructions End Bracket Installation, Brackets, Counterbalance Springs

Contents

Your Copyright 2008 Wayne-Dalton Corp. Part No Rev 2 7/16/2008Network For Package Contents Look for this symbol When Installing a NEW Door with AN Idrive Eyes to Prevent Possible Severe or Fatal Injury Pre-InstallationInspection Tools Needed System RequirementsWAYNE-DALTON Track Radius Photoelectric LOW Head Door Models below require the use of photo eyes Deﬁnition of key words used in this manual Table of Contents Drum Wrap & End Bracket Retro-Fit InstallationRemoval Spring Tension Removal Bracket and Gear End Bracket RemovalCenter Bracket & Cable Drum Powerful Spring Releasing ITS Retro-Fit InstallationEven Fatal Injury IMPORTANT! Right and Left Hand is Removal End Bracket Removal Vertical Track Height Adjustment Re-Install If NecessaryTop Bracket 8000/8100/8200 Track Tracks to the Support Before Opening Door can Cause Door Top Roller AdjustmentFailure to RE-ATTACH Horizontal Assembling Opener Installation Cable Drums Secure end bracket to the flag angle using Tools Needed Power Drill Socket Driver Wrench Step LadderEnd Brackets Repeat for other end bracket Cable Drum/ Drive Gear Installation Counterbalance Springs End Bracket InstallationBrackets Support Bracket Positioning Support BracketAttaching Opener To Pliers Attaching Disconnect CableBracket Slack between opener and right end Mounting Disconnect Pilot drill lag screw location using 1/8 drill bitHandle Bracket 6ft Disconnect Handle Usage Attaching Disconnect Handle Springs Cable Adjustments Tools Needed Vice Clamps Securing DoorFor Spring Winding Hands Winding Springs Recommended Spring Turns Drum Wrap InstallationTools Needed IMPORTANT! do not Overwind Springs Problems Setting Spring TensionIMPORTANT! do not Overwind SCREWS. for Detailed Information on Mounting Wall Station Drum Wrap Installation Installing Battery Disconnect Power to Installing the Light FixtureInstall hole plug into the screw hole in the light fixture If Included Power Cord Connecting OpenerAttaching Diffuser If Included Sensor Unit For Proper Alignment View of the Opener from the Front Sensor Wire Installation Checking for Obstructions Safety Sensor Alignment Programming Light Fixture On when program button is pushedProfile Routine Standard Upper Limit On and remain on for 30 seconds Work Properly Adjusting DetentProfile Routine Custom Upper Limit Confirm adjustment Lock Arm InstallationTurn increments Tools Needed Tape Measure Step Ladder Contact Obstruction Test Lock Arm Installation Fatal Injury MAY Result Testing the Safety Sensors Door activation Read and Follow ALL InstructionsEmergency Disconnect Never GO Under a STOPPED, Partially Open Door Operating the Wireless Wall Station Teaching HomeLink to the idrive opener Programming/Training HomeLink Unit Programming/Training HomeLink Unit Custom pet position Customizing the SettingsMulti-Door Programming For more profile options go to page 28 Maintenance Reconnect Power Power Connection Permanent Wiring OptionConfirm pot nut position* shown below Potentiometer Gear Handle In Manual Door Operated Position Motor Up Position Stations or Transmitters to OpenerProgramming Wireless WallRed Program Button Light Button Large Button Symptom Probable Cause Corrective Action Troubleshooting Lock Arm Troubleshooting Dalton dealer or distributor Pre-drill 3/32 pilot hole Cut-Out Template to Aid InstallationPre-drill 5/64 pilot hole Thank you for your purchase Models 3790/3790-Z Patent Information