TorqueMaster® Installation |
|
|
|
|
| |
2 | Cable Drum/ Drive Gear | TorqueMaster® Spring Tube |
| 1/2 Wrap | ||
Assembly (Cam Peak Straight Up) |
| |||||
|
| |||||
| Installation |
|
|
|
|
|
Tools Needed: | NOTE: If you just installed the |
|
|
|
|
|
Step Ladder | Torquemaster® Plus counterbalance, |
|
|
|
| Counterbalance |
continue with Step 4 on page 12. If you | Winding |
| ||||
|
| Cable | ||||
| have the Torquemaster® counterbalance |
| Shaft | Splines |
| |
|
|
|
| |||
|
|
|
|
| ||
|
|
| Groove |
|
| |
| system, complete Steps |
|
| Cable Drum |
|
|
| and 11. |
|
| (Right hand cable drum shown, left |
| |
|
|
| hand cable drum is symmetrically | Flag Angle | ||
|
|
|
| |||
| Shake the torque tube gently to extend the |
|
| opposite) |
|
|
| winding shafts out about 5" on each side. |
|
|
|
|
|
| For single spring applications, there will be |
|
| Cam Peak | Winding | Winding |
| no left hand spring in the torque tube. |
|
| Shaft Groove aligned | ||
|
|
| Straight Up | Shaft Groove | ||
|
|
| and seated in round | |||
|
|
|
|
|
| |
| Lift the torque tube and rest it on the top of |
|
|
|
| notch. |
|
|
|
|
|
| |
| the flagangles. Orient torque tube so that |
|
|
|
|
|
| back of opener is flat against header/ |
|
|
| Round |
|
| mounting surface. | Torque |
|
| Notch |
|
|
| Cable Drum |
|
| ||
| NOTE: Cable drums and torque tube are | Tube |
|
|
| |
|
|
|
|
|
| |
| cam shaped to fit together only one way. |
|
|
|
|
|
|
|
|
|
|
| |
| with the counter balance cable 1/2 wrap |
|
|
|
|
|
| (see illustrations). |
|
|
|
|
|
| To install the cable drum, slide the cable | Left Hand Side |
| Cam Peak | ||
|
| Straight Up | ||||
| drum over the winding shaft until the cable |
|
|
| Groove | |
| Single Spring Application |
| ||||
| drum seats against the torque tube. The |
|
| |||
|
|
|
|
|
| |
| winding shaft must extend past the cable |
|
|
|
|
|
| drum far enough to expose the splines and |
|
|
|
|
|
| the groove. |
|
|
| Round |
|
| Align the winding shaft groove with |
|
|
| Loose | |
|
|
|
| Notch | ||
| the round notch in the flagangle. |
|
|
|
| Winding |
|
|
|
|
| Shaft | |
|
|
|
|
|
| |
| For double spring applications, repeat for |
|
|
|
|
|
| opposite side. |
| Cable |
|
| |
|
|
| Drum |
| Flagangle | |
| For single spring applications, |
|
|
|
| |
| left hand Torquemaster® cable drum with |
|
|
|
|
|
| counter balance cable 1/2 wrap and insert |
|
| Cable |
|
|
| loose winding shaft into the cable drum |
|
| Drum | Winding |
|
|
|
|
|
| ||
| prior to sliding the cable drum over the |
|
|
| Shaft Splines |
|
|
|
|
|
|
| |
| torque tube. |
|
|
|
| Lubricating |
| NOTE: On single spring applications, take |
|
|
|
| |
|
|
|
|
| Oil | |
| care in handling the loose winding shaft |
|
|
|
|
|
| (left side) so that it does not slide back into |
|
|
|
|
|
| the torque tube. |
|
| Flagangle |
| Drive |
| Beginning with the right hand side, lubricate |
|
|
|
| Gear |
|
|
|
|
|
| |
| entire circumference of the drive gear |
|
|
|
|
|
| with lubricating oil. Slide the drive gear onto |
|
|
| Cable |
|
| the winding shaft splines until it touches |
|
|
| Drum |
|
|
|
|
|
|
| |
| the flagangle. |
|
|
|
|
|
| NOTE: On single spring applications, |
|
|
|
|
|
| no drive gear is required on the left side. |
|
|
|
| Drive |
| NOTE: If additional lubricating oil is |
|
|
|
| Gear |
|
|
|
|
|
| |
| required |
|
|
|
| Winding |
| is recommended. |
|
|
|
| Shaft |
10Please Do Not Return This Product To The Store. Call Us Directly! Our Trained Technicians Will Answer Your Questions and/or Ship Any Parts You May Need.
You can reach us Toll Free at
