Manuals / Wayne-Dalton / Household Appliance / Garage Door Opener

Wayne-Dalton 9600 Adjusting Top Brackets, Installation, the top bracket slide, out against the

Models: 9600 9100 9400

1 40

Page 17


	13	Adjusting Top Brackets
		Adjusting Top Brackets

	Tools Needed:	With horizontal tracks installed, you can
	7/16” Wrench	now adjust the top brackets. Vertically
	7/16” Wrench	align the top section of the door with the
		align the top section of the door with the
	Step Ladder	lower sections. Once aligned, position
	Step Ladder	the top bracket slide, out against the
		the top bracket slide, out against the
		horizontal track.
		Maintaining the slide’s position, tighten
		the (2) 1/4”- 20 flange hex nuts to
		secure the top bracket slide to the top
		bracket base.

HORIZONTAL

track

TOP

ROLLER

TOP

BRACKET

SLIDE

top	(2) 1/4”- 20
section	FLANGE HEX

NUTS

top
section	top

section

INSTALLATION

Correct

inCorrect

Please Do Not Return This Product To The Store. Contact your local Wayne-Dalton dealer. To find your local Wayne-Dalton dealer, refer to your

local yellow pages/business listings or go to the Find a Dealer section online at www.wayne-dalton.com

Page 17

Image 17

Wayne-Dalton 9600, 9400 Adjusting Top Brackets, Installation, the top bracket slide, out against the, horizontal track

Contents

TorqueMaster Plus - Single and Double Spring 9100, 9400 and 9600 SeriesTable of Contents Definition of key words used in this manualPackage Contents Door Section Identification Removing An Existing Door Tools RequiredFailure to securely attach asuitable mounting pad to structurally sound framing could cause springs toInstalling Q.I. Jamb Brackets InstallationINSTALLATION Cutting Vertical Track andAttaching Fully Adjustable Installing Q.I. Jamb Brackets ContinuedFlagangle to Vertical Track Tools Needed Tape Measure Hacksaw Power DrillBottom Section Counterbalance DrumsVertical Track INSTALLATION Stacking SectionsTop Brackets INSTALLATION U-BarU-Bar- Asymmetrical U ar Operator BracketINSTALLATION Top SectionPOSITION CAUSING SEVERE OR Fully Adjustable FlagangleAttaching Horizontal Track to DO NOT RAISE DOOR UNTILINSTALLATION Adjusting Top Bracketsthe top bracket slide, out against the horizontal trackCenter Bracket Bushing TorqueMaster Spring TubeINSTALLATION Drum Wrapstube assembly with the tabs facing THE GARAGE LOOKING OUTCable Drums INSTALLATION End Bracketssecurely attached to both End BracketsSecuring Center Bracket AssemblyNOTE If you are not installing the assembly, follow these instructionsINSTALLATION Securing Doorfor Spring Winding Cable must be taut and in Cable Adjustmentthe spiral, or thread, of the cable drumit is recommended that leather Winding Springsgloves be worn while winding the TorqueMaster Plus springsWinding Springs Continued Drum Wrap Installationraising door further can result in door falling andINSTALLATION Rear SupportTools Needed Rear Support Continueddoors 1. Check the door for levelATTEMPTING TO RESET THE TorqueMaster Plus ResetOF THE PROCEDURES, DO NOT InstructionsTorqueMaster Plus Reset Instructions ContinuedTools Needed TorqueMaster Plus ResetInstructions Continued DO NOT INSTALL PULL ROPES ROPE CAUSING SEVERE ORSide Lock Pull RopeStep Plate optional INSTALLATIONTrolley Installation for Standard Lift optional INSTALLATION Trolley Installation for Low HeadroomINSTALLATION INSTRUCTIONS AT TIME OF INSTALLATIONENSURE THAT DOOR SAFETY FEATURES FUNCTION. FAILUREPainting Cleaningmaintenance Painting Continued Lifetime Limited Warranty Models Please Do Not Return This Product To The Store Thank you for your purchase

Adjusting Top Brackets

the top bracket slide, out against the

horizontal track.

the (2) 1/4”- 20 flange hex nuts to

bracket base.