Manuals / Wayne-Dalton / Household Appliance / Garage Door Opener

Wayne-Dalton 9100, 9400 Securing Center Bracket, Assembly, NOTE If you are not installing the

Models: 9600 9100 9400

1 40

Page 22


	19	Securing Center Bracket
		Securing Center Bracket
		Assembly

	Tools Needed:	NOTE: If you are not installing the
	Power Drill	idrive® opener on your garage door, you
	Power Drill	must install the center bracket bushing
	7/16” Socket	assembly, follow these instructions.
	7/16” Socket
	Driver	To locate the center bracket, mark the
		To locate the center bracket, mark the
	3//16” Drill Bit	header halfway between the flagangles
	3//16” Drill Bit	and level the TorqueMaster® spring
		and level the TorqueMaster® spring
	Step Ladder	tube. Drill 3/16” pilot holes into header
	Step Ladder	for the lag screws. Fasten the metal
		for the lag screws. Fasten the metal
		bracket to the header using
		(2) 5/16” x 2” lag screws.

CENTER

BRACKET bushing

ASSEMBLY

(2) 5/16” x 2” hex head lag screws

Please Do Not Return This Product To The Store. Contact your local Wayne-Dalton dealer. To find your local Wayne-Dalton dealer, refer to your

local yellow pages/business listings or go to the Find a Dealer section online at www.wayne-dalton.com

Page 22

Image 22

Wayne-Dalton 9100 Securing Center Bracket, Assembly, NOTE If you are not installing the, and level the TorqueMaster spring

Contents

9100, 9400 and 9600 Series TorqueMaster Plus - Single and Double SpringDefinition of key words used in this manual Table of ContentsPackage Contents Door Section Identification Tools Required Removing An Existing Doorsuitable mounting pad to structurally securely attach aFailure to sound framing could cause springs toINSTALLATION InstallationInstalling Q.I. Jamb Brackets Cutting Vertical Track andFlagangle to Vertical Track Installing Q.I. Jamb Brackets ContinuedAttaching Fully Adjustable Tools Needed Tape Measure Hacksaw Power DrillCounterbalance Drums Bottom SectionVertical Track Stacking Sections INSTALLATIONTop Brackets U-Bar- Asymmetrical U-BarINSTALLATION Operator Bracket U arTop Section INSTALLATIONAttaching Horizontal Track to Fully Adjustable FlaganglePOSITION CAUSING SEVERE OR DO NOT RAISE DOOR UNTILthe top bracket slide, out against the Adjusting Top BracketsINSTALLATION horizontal trackTorqueMaster Spring Tube Center Bracket Bushingtube assembly with the tabs facing Drum WrapsINSTALLATION THE GARAGE LOOKING OUTCable Drums securely attached to both End End BracketsINSTALLATION BracketsNOTE If you are not installing the AssemblySecuring Center Bracket assembly, follow these instructionsfor Spring Winding Securing DoorINSTALLATION the spiral, or thread, of the Cable AdjustmentCable must be taut and in cable drumgloves be worn while winding Winding Springsit is recommended that leather the TorqueMaster Plus springsraising door further can Drum Wrap InstallationWinding Springs Continued result in door falling andRear Support INSTALLATIONdoors Rear Support ContinuedTools Needed 1. Check the door for levelOF THE PROCEDURES, DO NOT TorqueMaster Plus ResetATTEMPTING TO RESET THE InstructionsInstructions Continued TorqueMaster Plus ResetInstructions Continued TorqueMaster Plus ResetTools Needed Side Lock ROPE CAUSING SEVERE ORDO NOT INSTALL PULL ROPES Pull Ropeoptional INSTALLATION Step PlateTrolley Installation for Standard Lift Trolley Installation for Low Headroom optional INSTALLATIONENSURE THAT DOOR SAFETY AT TIME OF INSTALLATIONINSTALLATION INSTRUCTIONS FEATURES FUNCTION. FAILUREmaintenance CleaningPainting Painting Continued Lifetime Limited Warranty Models Thank you for your purchase Please Do Not Return This Product To The Store

Securing Center Bracket

Assembly

assembly, follow these instructions.

and level the TorqueMaster® spring

for the lag screws. Fasten the metal

bracket to the header using

(2) 5/16” x 2” lag screws.