| TorqueMaster® Plus Reset |
|
|
|
| Instructions Continued... |
|
|
|
Tools Needed: | 4. Now is a good time to remove vehicles |
|
|
|
| or items from garage to provide clear |
|
|
|
| access to end brackets. |
|
|
|
| 5. Flip the ratchet pawl knob on both |
|
|
|
| end brackets to the upper position (see |
|
|
|
| illustration). |
|
|
|
| 6. Raise door |
|
| place vice clamps |
|
|
| BELOW BOTTOM SECTION | |
| door. Repeat process until |
|
| on both vertical track |
| device resets (see disengaged system |
|
|
|
| illustration on previous page). |
|
|
|
| IMPORTANT: BE PREPARED TO SUPPORT |
|
|
|
| THE TOTAL WEIGHT OF THE DOOR. |
|
|
|
| 7. Cautiously remove the vice clamps |
|
|
|
| from the vertical tracks. With assistance, | Lower Position |
| UPPER Position |
| lower the door. |
|
|
|
| 8. Check for spring tension. Starting on |
|
|
|
| the right hand side, place a ratchet and |
|
|
|
| 5/8” socket on the TorqueMaster® Plus |
|
|
|
| winding shaft (see illustration). Ensure |
|
|
|
| ratchet is set so that it will tighten |
|
|
|
| counter clockwise on the right hand side, |
|
|
|
| and clockwise on the left hand side (if |
|
|
|
| applicable). If tension is present, remove |
|
|
|
| the ratchet and check the left hand side |
|
|
|
| (if applicable). If spring(s) have tension, |
|
|
|
| proceed to Balancing Door; if no spring |
|
|
|
| tension is present, contact a qualified |
|
|
|
| door systems technician to replace the |
|
|
|
| spring(s). |
|
|
|
| WARNING | Pawl Knob in Lower |
| Pawl knob in UPPER |
|
|
|
| |
| TO AVOID POSSIBLE INJURY, HAVE A | Position |
| Position |
|
|
|
| |
| TRAINED DOOR SYSTEM TECHNICIAN |
|
|
|
| MAKE ADJUSTMENTS/REPAIRS TO |
|
|
|
| CABLES, SPRING ASSEMBLIES AND |
|
|
|
| OTHER HARDWARE. |
|
|
|
| BALANCING DOOR |
|
|
|
| Lift door and check its balance. Adjust |
| End Bracket | Ratchet |
| spring(s), if door lifts by itself (hard to pull |
|
| |
| down) or if door is difficult to lift (easy to |
|
| with 5/8” |
| pull down). Anytime spring adjustments |
|
| Socket |
|
|
|
| |
| are made, ratchet pawl knob must be in |
|
|
|
| the upper position (see illustration). |
|
|
|
| An unbalanced door such as this can |
|
|
|
| cause idrive® or TorqueMaster® Plus |
|
|
|
| operation problems. To adjust spring(s), | PAWL |
|
|
| only add or remove a maximum of 3/10 |
|
| |
|
|
|
| |
| of a turn (three teeth of ratchet wheel) at |
| 3” Extension | |
| a time. Both sides need to be adjusted |
| ||
|
|
|
| |
30 |
|
|
|
|
Please Do Not Return This Product To The Store. Contact your local
local yellow pages/business listings or go to the Find a Dealer section online at
