Maximum Gain, Power Supply, Input Module, Group Module | X2 X2

Specifications

MIC Nominal Input Level	-56 dBu to -8 dBu
LINE Nominal Input Level	-44 dBu to +4 dBu
TAPE Nominal Input Level	+4 dBu / -10 dBV Switchable
Maximum Gain:
MIC to L/R Master Out	70 dB
MIC to L/R Group Out	70 dB
MIC to Aux Sends	68 dB
Power Supply:
X2 Maximum Power	210 Watts
U.L. Rating	300 Watts
Input Module (24):
Phantom Power	Aux Source Selector
Mic/Line Selector	Monitor Pan
Phase (Ø) Reverse	Monitor Peak LED Indicator
Mic/Line Gain	Monitor Solo
Channel/Monitor Reverse	Monitor Mute
High-Pass Filter	Monitor L/R Assign
Hi EQ	45mm Monitor Fader
EQ to Monitor Selector	Channel Pan
Low EQ	Channel Peak LED Indicator
Hi Mid Gain	Channel Solo
Hi Mid Frequency	Channel Mute
Hi Mid Bandwidth (Q)	Direct Source Selector
Lo Mid Gain	Channel L/R Assign
Lo Mid Frequency	Group Assign Selectors (1–8)
Lo Mid Bandwidth (Q)	Aux 1-2, 3-4, 5-6, 7-8
Aux Source Selector	Aux 1-2 Pan
Group Module (4):
Aux Level (A/B)	Solo (A/B)
Hi EQ (A/B)	Mute (A/B)
Lo EQ (A/B)	Group Assign Left
Stereo Separation (A/B)	Group Assign Right
Balance (A/B)	Pre-Fade-Listen
Aux 1-2 Send (A/B)	Mute
Assign Switches 1–8 and L/R Mix (A)	100mm Group Master Faders
Group Master Assign (B)
Master Module:
Dynamic Mute Automation Controls	CR Source Selectors (L/R, Aux 1-2,
Solo Mute	Ext. 1, Ext. 2)
3-Frequency Oscillator	Phones Level
Solo Master Level	Dim Switch
Aux Masters (8)	Mono Switch
Aux Masters AFL (8)	Talkback Mic
Aux Masters Mute (8)	Mic Level
Studio Level	Slate Switch
Studio CR/Aux 1-2 Selector	Studio Talkback Switch
Control Room Level	100mm L/R Master Faders

96	X2 Reference Manual

Image 97

X2 X2 manual Maximum Gain, Power Supply, Input Module, Group Module, Master Module

Contents

Alesis Introduction How To Use This ManualConventions Description of Controls. a dictionary of each control X2 Reference Manual Contents Applications Description of Controls Trouble-Shooting Midi Implementation Chart Page About Introduction Recording/Tracking Basic Principles of Mixing & Multitrack RecordingMonitoring Mixdown Introduction X2 Reference Manual Recorder/Mix Systems Guided TourPage Aux Send/Return Systems Muting Automation Control Room SystemsMeter Bridge Page Page Power Supply PowerConnections Unpacking and Inspection To connect the power supply to To Eliminate HUM if the Above has Failed Avoiding Ground Loops Balanced Mic Inputs Channel Inputs and OutputsUnbalanced Line Inputs Page Tape Input +4/-10 SwitchTape Send Direct Output Insert To connect an Elco cable to Balanced Tape I/O Group Outputs Stereo Returns and GroupsGroup Inserts Aux a & B Returns Master Outputs Master Inputs and OutputsMaster Inserts Control Room OutputsPage Adat Sync HeadphonesTo synchronize the X2 to an Adat system Examples of Connections Input Connector Type To interface with a typical unbalanced multitrack recorder Interfacing to an Unbalanced -10 dBV Multitrack Recorder Interfacing to a Professional +4 dBu Multitrack Recorder Interfacing to a Multitrack Recorder via a Patchbay Interfacing to Adat Using Elco ConnectorsInterfacing to the Mixdown Deck To connect the mixdown deck to Interfacing to the Studio Interfacing to the Control RoomInterfacing to the Headphone Amp Interfacing Aux Sends and Returns to Outboard Effects Connecting Simultaneously, if desired Interfacing with a Midi Sequencer Interfacing the InsertsTo interface a Midi sequencer with Applications Setting LevelsRecording II. Maintain Proper Fader Levels To record a single source to a single track Recording a Single Source to One Track To record two or more sources to a single track Recording Multiple Sources to One Track To record multiple sources to two tracks stereo Recording Multiple Sources to Two Tracks Stereo Recording Tips To select the meter bridge modeAbout Metering To listen to tape tracks on the Monitor faders OverdubbingTo listen to tape tracks on the Channel faders Applications Previous section X2 Reference Manual Monitoring Midi Virtual Tracks Getting the Mix to the HeadphonesTo route the mix to a headphone amp Selecting an Aux Send Adding EffectsTo set the level going to the effects device To hear effects in the headphone/cue mix To hear effects in the monitorsTo record effects onto the multitrack To record effects onto the mixdown deck Bouncing TracksTo bounce one or more tracks to another track mono To bounce multiple tracks to two tracks stereo Mixdown Basics Playback/Mix-DownGetting the Mix to the Tape Deck Here is a simplified step-by-step way to establish a mix To create a dependable mix Creating a Dependable Mix Mute Automation Page To configure the X2 mixer in order to achieve a mono mix Using Group Faders as SubgroupsLive Performance Creating a Monitor Mix Stage Monitor Mix Video Post-ProductionTo create two different stage monitor mixes Applications X2 Reference Manual Overview Mute Automation Destructive Solo To enable destructive solo modeMute Groups Page To define Mute Groups Defining Mute Groups Overlay Button Recalling Mute GroupsTo recall a Mute Group To return the console to its previous mute status Synchronization Display ModeSelecting a Sync Source Getting On-line/Locking Recording and Playing Back Mute Events Mute EventsUndoing Mute Events OverdubbingPage Erasing Editing Songs To erase all events on one or more channels Erase All MemoryTo erase all events on all channels To erase a Song including its mute events and 4 Mute Groups Copy Mute Events CopyingCopy Song To copy mute events from one channel to another Selecting Songs via Midi Midi ChannelTo set the Midi channel Midi Map Transmitting System Exclusive Memory BackupReceiving System Exclusive Remaining Memory Input Channel Controls Description of Controls To MON Switch HPF SwitchHi and Lo EQ Hi Mid and Lo Mid EQ Switch Aux 3/4 EQ in SwitchAUX Source Switch AUX 1-2, AUX 1-2 PAN Monitor PAN Switch Aux 5/6Monitor Peak LED Monitor Solo Button Group Assign Switches 1-2, 3-4, 5-6 DIR SwitchChannel PAN Channel Peak LED Stereo Aux Return Controls Aux Master Controls Group Masters Switch Aux B Only AUX a Assign Switches Aux a OnlyStereo Separation Balance Button Group Master ControlsSolo Button Mute Button Group 1-8 Master Faders Oscillator Frequency and Level Master ControlsSolo LED and Level Studio Level and Assignment Control Room Level and Source PhonesMaster Faders Meter BridgePage Display Mute Automation Controls Mute Groups Online Memory Remaining Erase FWD and Erase BWD Buttons Mute Solo Erasing Memory Description of Controls X2 Reference Manual Trouble-Shooting Index TROUBLE-SHOOTINGChecking the Software Version Re-initializing Cleaning and Maintenance Maintenance/ServiceWarranty Information Obtaining Repair Service Customers outside the USA Trouble-Shooting X2 Reference Manual Maps Midi Maps IndexMute Midi Note Number Mute Midi Controller Number Map Map Number Interval Midi Implementation Chart Specifications Maximum Gain Power SupplyInput Module Group Module Weight DimensionsTotal Shipping Weight Dimensional Drawings Internal Connector Pinouts Block Diagram Solo Index Song LED 102