Specifications | X2 X2 instruction

Specifications

SPECIFICATIONS

All measurements taken with an Audio Precision System One. All noise measurements taken with trim at minimum and faders at unity gain with 22 Hz to 22 kHz bandwidth unless otherwise specified. All Tape In & Out measurements made on balanced +4 dBu connectors. (+4 dBu into a line input with minimum trim & faders at unity “0” will yield +4 dBu at any balanced output.)

Frequency Response:

Noise:

MIC/LINE to Tape Out MIC/LINE to L/R Master Out MIC/LINE to Tape Out via Group Tape In to Tape Out

Tape In to L/R Master Out Tape In to Tape Out via Group

10 Hz – 75 kHz ± 1 dB (any input to any output @ nominal operating levels)

-85 dBu -85 dBu -81 dBu -85 dBu -87 dBu -82 dBu

Mix Output Noise:
24 Tape Inputs assigned to L/R Master Out	-74 dBu
Signal to Noise:
MIC/LINE to L/R Master Out	89 dB
Dynamic Range:
MIC/LINE to L/R Master Out	113 dB
Headroom:
Internal to Console	24 dB
External above +4 dBu Balanced Outputs	24 dB
Maximum Output Level:
Balanced Outputs into 10k ohm Load	+28 dBu
Balanced Outputs into 600 ohm Load	+26 dBu

THD + Noise @ 1 kHz (+20 dBu Input - Unity Gain):

MIC/LINE to Tape Out

MIC/LINE to L/R Master Out

Tape In to L/R Master Out

Attenuation (1 kHz):

CHANNEL fader

CHANNEL MUTE AUTOMATION BUSS ASSIGN ISOLATION CROSSTALK

Equivalent Input Noise (22 Hz to 22 kHz):

MIC w/ 150 ohm termination

<0.005%, 0.003% typical <0.005%, 0.003% typical <0.004%, 0.002% typical

>83dB, 88 dB typical >95 dB, 100 dB typical >100 dB, 103 dB typical 70 dB typical

-128 dBu

Input Levels:

X2 Reference Manual

95

Image 96

X2 X2 manual Specifications

Contents

Alesis How To Use This Manual IntroductionConventions Description of Controls. a dictionary of each control X2 Reference Manual Contents Applications Description of Controls Trouble-Shooting Midi Implementation Chart Page Introduction About Basic Principles of Mixing & Multitrack Recording Recording/TrackingMonitoring Mixdown Introduction X2 Reference Manual Guided Tour Recorder/Mix SystemsPage Aux Send/Return Systems Control Room Systems Muting AutomationMeter Bridge Page Page Power Power SupplyConnections Unpacking and Inspection To connect the power supply to Avoiding Ground Loops To Eliminate HUM if the Above has Failed Channel Inputs and Outputs Balanced Mic InputsUnbalanced Line Inputs Page +4/-10 Switch Tape InputTape Send Direct Output Insert Balanced Tape I/O To connect an Elco cable to Stereo Returns and Groups Group OutputsGroup Inserts Aux a & B Returns Master Inputs and Outputs Master OutputsMaster Inserts Control Room OutputsPage Headphones Adat SyncTo synchronize the X2 to an Adat system Input Connector Type Examples of Connections Interfacing to an Unbalanced -10 dBV Multitrack Recorder To interface with a typical unbalanced multitrack recorder Interfacing to a Professional +4 dBu Multitrack Recorder Interfacing to Adat Using Elco Connectors Interfacing to a Multitrack Recorder via a PatchbayInterfacing to the Mixdown Deck To connect the mixdown deck to Interfacing to the Control Room Interfacing to the StudioInterfacing to the Headphone Amp Interfacing Aux Sends and Returns to Outboard Effects Connecting Simultaneously, if desired Interfacing the Inserts Interfacing with a Midi SequencerTo interface a Midi sequencer with Setting Levels ApplicationsRecording II. Maintain Proper Fader Levels Recording a Single Source to One Track To record a single source to a single track Recording Multiple Sources to One Track To record two or more sources to a single track Recording Multiple Sources to Two Tracks Stereo To record multiple sources to two tracks stereo To select the meter bridge mode Recording TipsAbout Metering Overdubbing To listen to tape tracks on the Monitor fadersTo listen to tape tracks on the Channel faders Applications Previous section X2 Reference Manual Getting the Mix to the Headphones Monitoring Midi Virtual TracksTo route the mix to a headphone amp Adding Effects Selecting an Aux SendTo set the level going to the effects device To hear effects in the monitors To hear effects in the headphone/cue mixTo record effects onto the multitrack Bouncing Tracks To record effects onto the mixdown deckTo bounce one or more tracks to another track mono To bounce multiple tracks to two tracks stereo Playback/Mix-Down Mixdown BasicsGetting the Mix to the Tape Deck Here is a simplified step-by-step way to establish a mix Creating a Dependable Mix To create a dependable mix Mute Automation Page Using Group Faders as Subgroups To configure the X2 mixer in order to achieve a mono mixLive Performance Creating a Monitor Mix Video Post-Production Stage Monitor MixTo create two different stage monitor mixes Applications X2 Reference Manual Mute Automation Overview To enable destructive solo mode Destructive SoloMute Groups Page Defining Mute Groups To define Mute Groups Recalling Mute Groups Overlay ButtonTo recall a Mute Group To return the console to its previous mute status Display Mode SynchronizationSelecting a Sync Source Getting On-line/Locking Mute Events Recording and Playing Back Mute EventsUndoing Mute Events OverdubbingPage Editing Songs Erasing Erase All Memory To erase all events on one or more channelsTo erase all events on all channels To erase a Song including its mute events and 4 Mute Groups Copying Copy Mute EventsCopy Song To copy mute events from one channel to another Midi Channel Selecting Songs via MidiTo set the Midi channel Midi Map Memory Backup Transmitting System ExclusiveReceiving System Exclusive Remaining Memory Description of Controls Input Channel Controls HPF Switch To MON SwitchHi and Lo EQ Hi Mid and Lo Mid EQ EQ in Switch Switch Aux 3/4AUX Source Switch AUX 1-2, AUX 1-2 PAN Switch Aux 5/6 Monitor PANMonitor Peak LED Monitor Solo Button DIR Switch Group Assign Switches 1-2, 3-4, 5-6Channel PAN Channel Peak LED Aux Master Controls Stereo Aux Return Controls AUX a Assign Switches Aux a Only Group Masters Switch Aux B OnlyStereo Separation Balance Group Master Controls ButtonSolo Button Mute Button Group 1-8 Master Faders Master Controls Oscillator Frequency and LevelSolo LED and Level Studio Level and Assignment Phones Control Room Level and SourceMaster Faders Meter BridgePage Mute Automation Controls Display Mute Groups Online Erase FWD and Erase BWD Buttons Memory Remaining Erasing Memory Mute Solo Description of Controls X2 Reference Manual TROUBLE-SHOOTING Trouble-Shooting IndexChecking the Software Version Re-initializing Maintenance/Service Cleaning and MaintenanceWarranty Information Obtaining Repair Service Customers outside the USA Trouble-Shooting X2 Reference Manual Midi Maps Index MapsMute Midi Note Number Map Mute Midi Controller Number Map Number Interval Midi Implementation Chart Specifications Power Supply Maximum GainInput Module Group Module Dimensions WeightTotal Shipping Weight Dimensional Drawings Internal Connector Pinouts Block Diagram Index Solo Song LED 102