Mute Automation Controls, Display | X2 X2 specification

Description of Controls

Mute Automation Controls

DISPLAY

The DISPLAY button is used to cycle the 2-digit LED display through a cycle of four display modes: Song, Sync, Channel and Map. Each time the DISPLAY button is pressed, the display will advance to the next display mode.

The Display Mode is indicated by four LEDs (Song, Sync, Channel and Map). They are located directly above the LED display and the DISPLAY button.

INC & DEC

The INC/DEC buttons are to edit a value in the display. Press INC to raise the value, or press DEC to lower it. Holding either INC or DEC will cause the value in the display to scroll at a gradually increasing speed.

When the display is in SONG mode (SONG LED is lit) or CHANNEL mode (CHANNEL LED lit), you can get back to 00 quickly by pressing both INC and DEC buttons simultaneously.

SONG

The SONG LED indicates that the display is in Song mode. Use the INC/DEC buttons to select a Song from 00—99. Each Song contains four Mute Groups plus mute event information. Before recording new mute events or defining Mute Groups, be sure you have selected the desired Song already.

SYNC

The SYNC LED indicates that the display is in Sync mode. Use the INC/DEC buttons to select a Sync Source (ADAT Time Code, MIDI Time Code or MIDI Clock). You must select a sync source and be online (connected) with the sync source in order to use the Mute Automation’s on-board sequencer. For more information about sync sources and hook-up descriptions, refer to pages 23 and 49.

CHANNEL

The CHANNEL LED indicates that the display is in MIDI Channel mode. Use the INC/DEC buttons to select a MIDI channel from 01 to 16, or select 00 for Omni mode (all channels). This MIDI channel is used for transmitting and receiving mute events via MIDI using an external sequencer.

MAP

The MAP LED indicates that the display is in MIDI Map mode. Use the INC/DEC buttons to select one of the internal MIDI maps (1.1—1.4, 2.0—2.9). This determines how the console’s MUTES will be controlled via MIDI.

X2 Reference Manual

81

Image 82

X2 X2 manual Mute Automation Controls, Display

Contents

Alesis Conventions How To Use This ManualIntroduction Description of Controls. a dictionary of each control X2 Reference Manual Contents Applications Description of Controls Trouble-Shooting Midi Implementation Chart Page Introduction About Recording/Tracking Basic Principles of Mixing & Multitrack RecordingMonitoring Mixdown Introduction X2 Reference Manual Guided Tour Recorder/Mix SystemsPage Aux Send/Return Systems Muting Automation Control Room SystemsMeter Bridge Page Page Connections PowerPower Supply Unpacking and Inspection To connect the power supply to Avoiding Ground Loops To Eliminate HUM if the Above has Failed Balanced Mic Inputs Channel Inputs and OutputsUnbalanced Line Inputs Page Tape Send Direct Output +4/-10 SwitchTape Input Insert Balanced Tape I/O To connect an Elco cable to Group Inserts Stereo Returns and GroupsGroup Outputs Aux a & B Returns Master Inserts Master Inputs and OutputsMaster Outputs Control Room OutputsPage Adat Sync HeadphonesTo synchronize the X2 to an Adat system Input Connector Type Examples of Connections Interfacing to an Unbalanced -10 dBV Multitrack Recorder To interface with a typical unbalanced multitrack recorder Interfacing to a Professional +4 dBu Multitrack Recorder Interfacing to the Mixdown Deck Interfacing to Adat Using Elco ConnectorsInterfacing to a Multitrack Recorder via a Patchbay To connect the mixdown deck to Interfacing to the Headphone Amp Interfacing to the Control RoomInterfacing to the Studio Interfacing Aux Sends and Returns to Outboard Effects Connecting Simultaneously, if desired Interfacing with a Midi Sequencer Interfacing the InsertsTo interface a Midi sequencer with Recording Setting LevelsApplications II. Maintain Proper Fader Levels Recording a Single Source to One Track To record a single source to a single track Recording Multiple Sources to One Track To record two or more sources to a single track Recording Multiple Sources to Two Tracks Stereo To record multiple sources to two tracks stereo Recording Tips To select the meter bridge modeAbout Metering To listen to tape tracks on the Monitor faders OverdubbingTo listen to tape tracks on the Channel faders Applications Previous section X2 Reference Manual Monitoring Midi Virtual Tracks Getting the Mix to the HeadphonesTo route the mix to a headphone amp Selecting an Aux Send Adding EffectsTo set the level going to the effects device To hear effects in the headphone/cue mix To hear effects in the monitorsTo record effects onto the multitrack To bounce one or more tracks to another track mono Bouncing TracksTo record effects onto the mixdown deck To bounce multiple tracks to two tracks stereo Getting the Mix to the Tape Deck Playback/Mix-DownMixdown Basics Here is a simplified step-by-step way to establish a mix Creating a Dependable Mix To create a dependable mix Mute Automation Page Live Performance Using Group Faders as SubgroupsTo configure the X2 mixer in order to achieve a mono mix Creating a Monitor Mix Stage Monitor Mix Video Post-ProductionTo create two different stage monitor mixes Applications X2 Reference Manual Mute Automation Overview Destructive Solo To enable destructive solo modeMute Groups Page Defining Mute Groups To define Mute Groups To recall a Mute Group Recalling Mute GroupsOverlay Button To return the console to its previous mute status Selecting a Sync Source Display ModeSynchronization Getting On-line/Locking Undoing Mute Events Mute EventsRecording and Playing Back Mute Events OverdubbingPage Editing Songs Erasing To erase all events on all channels Erase All MemoryTo erase all events on one or more channels To erase a Song including its mute events and 4 Mute Groups Copy Song CopyingCopy Mute Events To copy mute events from one channel to another Selecting Songs via Midi Midi ChannelTo set the Midi channel Midi Map Receiving System Exclusive Memory BackupTransmitting System Exclusive Remaining Memory Description of Controls Input Channel Controls Hi and Lo EQ HPF SwitchTo MON Switch Hi Mid and Lo Mid EQ AUX Source Switch EQ in SwitchSwitch Aux 3/4 AUX 1-2, AUX 1-2 PAN Monitor Peak LED Switch Aux 5/6Monitor PAN Monitor Solo Button Channel PAN DIR SwitchGroup Assign Switches 1-2, 3-4, 5-6 Channel Peak LED Aux Master Controls Stereo Aux Return Controls Stereo Separation AUX a Assign Switches Aux a OnlyGroup Masters Switch Aux B Only Balance Solo Button Group Master ControlsButton Mute Button Group 1-8 Master Faders Solo LED and Level Master ControlsOscillator Frequency and Level Studio Level and Assignment Master Faders PhonesControl Room Level and Source Meter BridgePage Mute Automation Controls Display Mute Groups Online Erase FWD and Erase BWD Buttons Memory Remaining Erasing Memory Mute Solo Description of Controls X2 Reference Manual Checking the Software Version TROUBLE-SHOOTINGTrouble-Shooting Index Re-initializing Warranty Information Maintenance/ServiceCleaning and Maintenance Obtaining Repair Service Customers outside the USA Trouble-Shooting X2 Reference Manual Maps Midi Maps IndexMute Midi Note Number Map Mute Midi Controller Number Map Number Interval Midi Implementation Chart Specifications Input Module Power SupplyMaximum Gain Group Module Total Shipping Weight DimensionsWeight Dimensional Drawings Internal Connector Pinouts Block Diagram Index Solo Song LED 102