Manuals / Xantrex Technology / Computer Equipment / Power Supply

Xantrex Technology XFR 2800 manual Tool Required Phillips #2 screwdriver

Models: XFR 2800

1 90

Download 90 pages 12.58 Kb

Page 83

Tool Required: Phillips #2 screwdriver

Calibration

Calibration Setup

Removing Option Card If there is a GPIB or RS-232 option card (PCB) installed inside the power supply, you will have to remove it to access the calibration potentiometers.

Tool Required: Phillips #2 screwdriver

1.Turn OFF the power supply. Disconnect AC Power. Remove the cover.

2.Remove 4 screws from their standoffs inside the power supply to release the option card.

3.Remove 2 screws at the rear panel to release the option card’s sub-plate.

4.Unplug the ribbon cable connectors from the option card. Lift out card.

Figure 5.1

Programming and Monitoring Calibration Locations

(Top view.)

Release 2.1

81

Image 83

Xantrex Technology XFR 2800 manual Tool Required Phillips #2 screwdriver

Contents

Operating Manual XFR 2800 Watt Series Programmable DC Power SupplyXFR XFR XFR XFR XFR XFR XFR XFR XFR XFR Page Operating Manual for XFR 2800 Watt SeriesProgrammable DC Power Supply Limited Warranty How do you get service?Proof of purchase may be in any one of the following forms Disclaimer Product WARNING Limitations on Use Information About Your Power SupplyCautions Power Supply SafetyAbout This Manual Who Should Use This ManualMain Sections Manual RevisionsAbout This Manual Power Supply Safety MarkingsSection Features and Specifications ContentsSection 5. Calibration Section Local Operation Section Remote OperationList of Figures List of Figures Operating Manual for XFR 2.8kW Series Power SupplyList of Tables List of Tables Operating Manual for XFR 2.8kW Series Power SupplyDescription Section 1. Features and SpecificationsFeatures and Options External monitor signals for output voltage and current Section 3. Local Operation Front Panel Controls“Mechanical Specifications” on page “Functional Tests” on page Rear Panel Connectors and Switch Rear Panel Connectors and SwitchLow voltage 7.5 V to 100 V model shown Figure 1.2 Power Supply Rear Panelswitch enables you to choose Resetting the Switches Before making any changes to the switch settings, disable the power supply output by pushing the front panel STANDBY switch to its IN position. This temporarily shuts down the power supply. The front panel S/D LED turns on. Then, use any small, flat-bladed screwdriver to change the switch settings provides access to the following functions Name Features and SpecificationsConnector ReferenceMaking J2 Connections WiringNominal line voltage is 208 Vac, 60 Hz SpecificationsSpecifications are subject to change without notice 12-220 Features and SpecificationsModels 7.5-300Specifications Features and Specifications100-28 Features and SpecificationsModels 60-46Specifications Features and SpecificationsBased on 100 V, 28 A model Input ConditionsAdditional Specifications Remote Programming and Monitoring Additional FeaturesEnvironmental Specifications Mechanical Specifications 3.45 87.63 mm Figure 1.6 Dimensional DrawingsDimensions given are nominal Operating Manual for XFR 2.8kW Series Power SupplyIntroduction Section 2. InstallationBasic Setup Procedure Initial Inspection Periodic Cleaning Inspection, Cleaning, and PackagingIf you are returning a product from outside of the USA or Canada Returning Power Supplies to the ManufacturerPackaging for Shipping or Storage Rack Mounting Location, Mounting, and VentilationAC Input AC Input PowerAC Input Connector and Voltage Selection 60 C minimum, 300 AC Input Wire ConnectionTable 2.3 AC Wire Specification 3 x 12 AWG stranded copperAC Input Cover and Strain Relief Functional Tests Voltage Mode Operation CheckCurrent Mode Operation Check Front Panel Function Checks Load Connection Load WiringFigure 2.3 Maximum Load Wire Length for 1 V Line Drop Making Load ConnectionsTo detach the 2-part cover 1. Strip the ends of the wires 150 V to 600 V Models Figure 2.6 Output Voltage Connectorsense connector as identified on Figure 1.2, on page Loads the radial power distribution method Figure 2.10Multiple Loads with Remote Sensing InstallationOperating Manual for XFR 2.8kW Series Power Supply Local and Remote Sensing Sense WiringFunction InstallationTerminal NameUsing Remote Sensing 5. Turn the power supply ON Introduction Section 3. Local OperationStandard Operation Operating Modes and Automatic CrossoverFigure 3.1 Operating Modes Local Operationfront and rear panel diagrams Setting Output Voltage and Current Limit Front Panel OVP Operation Using Over Voltage Protection OVPTo reset the OVP circuit after it activates Controlling the Shutdown Function via the J2 Connector Using the Shutdown Function1. If switch SW1-7 is ON but there is no signal applied, the S/D LED turns on and the power supply will not provide an output until the HIGH signal level is applied Configuring Multiple Supplies for Series Operation Using Multiple SuppliesOperation ConfiguringMultiple ParallelSupplies for Split Supply Operation Figure 3.4 Split Supply Operation of Multiple Supplies Positive-negative SupplyFigure 3.5 Split Supply Operation of Multiple Supplies Local sense lines shown are default J10 connectionsPositive-negative Supply Over Temperature Protection OTP Over Temperature Protection OTPUnusual or Erratic Operation User DiagnosticsEmergency Shutdown Further Checks and Corrections SymptomLocal Operation CheckIntroduction Section 4. Remote OperationProgramming ProcedureRemote Analog Programming of Output Voltage and Current Limit Remote4. Connect the programming sources to the mating J2 connector as shown in Figure 4.1, observing the correct polarity for voltage sources. Ensure that the mating connector is plugged securely into the rear panel connector Remote Operation Remote Operation Figure 4.1 Connecting Programming Sources to J2 ConnectorRemote Monitoring of Output Voltage and Current Section 5. Calibration Calibration SetupService PrecautionsCalibration Calibration SetupAccessing Calibration Potentiometers Tool Required Phillips #2 screwdriver Voltage Programming Circuit Calibration Calibrating for Programming AccuracyCurrent Limit Programming Circuit Calibration Output Voltage Monitor Circuit Calibration Calibrating for Readback AccuracyOutput Current Monitor Circuit Calibration Calibrating for Readback Accuracy Operating Manual for XFR 2.8kW Series Power SupplyCalibration Page 800 667 8422 Toll Free North America prg.info@xantrex.com Xantrex Technology Inc8999 Nelson Way Burnaby, British Columbia Canada V5A 4B5 604 422 8595 Tel 604 421 3056 Fax