Ryobi RY 43160A manuel dutilisation Chain Tension, General Maintenance, Flats, See Figures 11

Page 16

MAINTENANCE

WARNING:

When servicing, use only identical replacement parts. Use of any other parts could create a hazard or cause product damage.

WARNING:

Always wear eye protection with side shields marked to comply with ANSI Z87.1, along with head protection. Failure to do so could result in objects being thrown into your eyes and other possible serious injuries.

WARNING:

Before inspecting, cleaning or servicing the unit, stop the motor, wait for all moving parts to stop, and disconnect from power supply. Failure to follow these instructions can result in serious personal injury or property damage.

FLATS

APPROX .050 in.

CHAIN TENSION

See Figures 11 - 12.

Fig. 11

Fig. 12

GENERAL MAINTENANCE

Avoid using solvents when cleaning plastic parts. Most plastics are susceptible to damage from various types of commercial solvents and may be damaged by their use. Use clean cloths to remove dirt, dust, oil, grease, etc.

WARNING:

Do not at any time let brake fluids, gasoline, petroleum-based products, penetrating oils, etc., come in contact with plastic parts. Chemicals can damage, weaken, or destroy plastic, which could result in serious personal injury.

All chain saw service, other than the items listed in the instruction manual maintenance instructions, should be performed by competent chain saw service personnel. (For example, if improper tool is used to hold the flywheel in order to remove the clutch, structural damage to the flywheel could occur and subsequently could cause the flywheel to burst).

WARNING:

To avoid possible serious injury, never touch or adjust the chain while the motor is running. The saw chain is very sharp; always wear protec- tive gloves when performing maintenance to the chain.

nStop the motor and disconnect from power supply before setting the chain tension. Make sure the guide bar nut is loose to finger tight, turn the chain tensioning screw clockwise to tension the chain. Refer to Replacing the Bar and Chain for additional information.

NOTE:  A cold chain is correctly tensioned when there is no slack on the underside of the guide bar, the chain is snug, but it can be turned by hand without binding.

nChain must be re-tensioned whenever the flats on the drive links hang out of the bar groove as shown in fig. 11.

nDuring normal operation, the temperature of the chain will increase. The drive links of a correctly tensioned warm chain will hang approximately

.050 in. out of the bar groove, as shown in fig. 12.

Page 16 — English

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Save this Manual for Future Reference ALL Versions Toutes LES Versions Todas LAS VersionesTable of Contents IntroductionImportant Safety Instructions Read ALL InstructionsSpecific Safety Rules 5 English Symbols Symbol Name ExplanationSymbol Signal Meaning Electrical Double InsulationElectrical Connection Extension CordsProduct Specifications OIL CAPTelescoping Pole LOCK-OUT Button Scabbard CordFeatures AssemblyCord Upperpowerhead Collarpole Connecting the PolesLower Collar Handle Pole Button Adding BAR and Chain Lubricant OperationApplications Connecting to Power Supply Adjusting Telescoping PoleLOCK-OUT Button Switch Trigger Cord Retainer Starting and StoppingBASIC Cutting Procedure Preparation for CuttingSee Figures 7 Collar Load Second CUTSee Figures 9 Limbing and PruningMaximum Maintenance General MaintenanceChain Tension FlatsReplacing the BAR and Chain See Figures 13Chain Maintenance Chain OilerBAR NUT Remove CAP BAR Lube Raker Depth Gauge ClearanceHOW to Sharpen the Cutters See Figures 19TOE Fig GulletTroubleshooting Problem Cause RemedyStoring the Product Refer to Replacing the Bar and Chain earlier in thisWarranty Limited Warranty StatementAVERTISSEMENT  Instructions Importantes Concernant LA SécuritéLire Toutes LES Instructions Règles DE Sécurité Particulières 5 Français Symboles Symbole NOM ExplicationSymbole Signal Signification AvisCaractéristiques Électriques Isolation DoubleAvertissement Connexion ÉlectriqueCaractéristiques Fiche TechniqueBouchon ’HUILEAssemblage Connexion DU LE Poignèe Colier Inférieur Bouton Arbre DE Poignèe Base FiletéeAppoint D’HUILE Pour Guide ET Chaîne UtilisationBouchon Réservoir ’HUILE Branchement SUR UNE Prise Secteur Démarrage ET ArrêtRéglage DU Manche Télescopique Voir la figureVoir les figures 7 et Préparation Pour LA CoupeMÉTHODE DE Coupe Élémentaire Ébranchage ET Émondage Voir les figures 9 etEntretien Entretien GénéralTension DE LA Chaîne MéplatsRemplacement DE LA Guide ET Chaîne Voir les figures 13 àEntretien DE LA Chaîne Système DE Lubrification DE LA Chaîne025 po Comment Affûter LES Dents Voir les figures 19 àProblème Cause Solution Voir Remplacement du guide et de la chaîne plus hautDépannage Remisage LE ProduitGarantie Énoncé DE LA Garantie LimitéeAdvertencia Instrucciones DE Seguridad ImportantesLEA Todas LAS Instrucciones Reglas DE Seguridad Específicas Página 5 Español Símbolos Símbolo Nombre ExplicaciónPrecaución PeligroSímbolo Señal Significado Aspectos Eléctricos Doble AislamientoConexión Eléctrica Cordones DE ExtensiónCaracterísticas Especificaciones DEL ProductoArmado Cómo Acoplar EL Mango Funcionamiento Abastecimiento DE Lubricante Para LA Barra Y LA CadenaAplicaciones Vea la figuraConexión AL Suministro DE Corriente Arranque Y ApagadoAjuste DE LA Pértiga Telescópica Vea las figuraPreparación Para EL Corte Desramado Y PodaCasquillo Carga Segundo Corte Corte Final Guía DE Corte60 Máximo Mantenimiento Mantenimiento GeneralTensión DE LA Cadena Partes PlanasReemplazo LA Barra Y Cadena Vea las figuras 13 aCadena BarraMantenimiento DE LA Cadena Lubricador DE LA CadenaPulg Forma DE Afilar LOS Dientes DE Corte Talón Puntera Garganta Dientes DE Corte IzquierdosProblema Causa Solución Solución DE ProblemasAlmacenamiento DE LA Producto Garantía Declaración DE LA Garantía LimitadaOPERATOR’S Manual / Electric Pole SAW Techtronic Industries North AMERICA, INCCalifornia Proposition Proposition 65 DE LA Californie
Top Page Image Contents