Remington Power Tools ST3010A owner manual Save These Instructions, While Operating Trimmer

Page 6
WHILE OPERATING

2 Chapter 1: Important Safety Information

10.Provide Ground Fault Circuit Inter- rupter (GFCI) protection on the circuit or outlet to be used for trimmer. You may use receptacles with built-in GFCI protection for this safety measure.

WHILE OPERATING

TRIMMER

1.Stay alert. Watch what you are doing. Use common sense.

2.Be aware of extension cord while operat- ing trimmer. Be careful not to trip over extension cord.

3.Avoid unintentional starting. Do not carry plugged-in trimmer with finger on switch. Be sure switch is OFF when plugging in trimmer.

4.Do not overreach. Keep proper foot- ing and balance at all times when operating trimmer.

5.Disconnect the trimmer from the power supply

•when not in use

•before servicing

6.Do not force trimmer. It will do the job better and with less likelihood of a risk of injury at the rate for which it was designed.

7.Do not abuse power cord. Never pull or carry trimmer by power cord. Never yank cord to disconnect from receptacle. Keep power cord from heat, oil, and sharp edges.

8.Keep hands and feet away from cut- ting area.

MAINTENANCE AND STORAGE OF TRIMMER

1.Maintain trimmer with care.

•Inspect trimmer cord periodically, and if damaged, have it repaired by a qualified service facility.

•Inspect extension cords periodically and replace if damaged.

•If trimmer is not working properly, has been dropped, damaged, left outdoors, or dropped into water, have it repaired by a qualified ser- vice center.

•Keep handles dry, clean, and free from oil and grease.

•Keep guards in place and in work- ing order.

2.Check damaged parts.

•If a part is damaged, carefully check the damaged part before using the trimmer. Make sure the part will operate properly and perform its intended function.

•Check for alignment of moving parts, binding of moving parts, breakage of parts, mounting, and any other condition that may affect its operation.

•A guard or other part that is dam- aged should be properly repaired or replaced by a qualified service center unless indicated elsewhere in this manual.

•Use only geniune Remington® replacement parts and accessories. These are available from your local dealer. Use of any non-Reming- ton® parts or accessories could lead to injury to the user, damage to the unit, and void you warranty.

3.Servicing of Double-Insulated Tools:

•In a double-insulated tool, two systems of insulation are provided instead of grounding. No ground- ing means is provided on a double- insulated tool, nor should a means for grounding be added to the tool. Servicing a double-insulated tool requires extreme care and knowl- edge of the system, and should be done only by qualified service personnel. Replacement parts for a double-insulated tool must be identical to the parts they replace.

4.Store idle trimmer indoors.When not in use, store trimmer and extension cord indoors in a dry location. Store trimmer above the reach of children or in a locked area out of the reach of children.

This manual is your guide to safe and proper operation of the trimmer.

SAVE THESE

INSTRUCTIONS.

118336

Page 5 Page 7
Image 6
Page 5 Page 7
Contents ELECTRIC TRIMMER MODEL ST3010ADouble Insulated 118336 Trimmer Maintenance Important Safety InformationTrimmer Assembly TroubleshootingWhere Purchased welcomeDate Purchased Model NumberBEFORE OPERATING TRIMMER 1 important safety informationSAFETY WARNINGS Cord LengthMAINTENANCE AND STORAGE OF TRIMMER SAVE THESE INSTRUCTIONSWHILE OPERATING TRIMMER H. Trigger Switch I. Trigger Switch Safety Button A A. Motor Housing B. Spool Housing C. Cutting Guard D. Front HandleE. Rear Handle F. Power Cord G. Extension Cord Retainer 2 product identificationWARNING Do not operate trimmer without guard or handle in place 3 trimmer assemblyAssembling Trimmer Attaching Cutting GuardConnecting Extension Cord 4 trimmer operationExtension Cords Starting the Trimmer WARNING The trimmer can throw debris, causing injury to those nearbyOperating the Trimmer TrimmingWARNING Blade is sharp. To prevent serious injury, do not touch blade Advancing Trimmer LineReplacing Trimmer Line Removing the Spool4. Measure out 30 feet of replacement line 8 Chapter 4 Trimmer OperationFigure 4-18 Replacing spool cover onto spool housing WARNING When cleaning trimmer Do not submerse in any liquids 5 trimmer maintenanceCleaning and Maintenance Do not use products that con- tain Ammonia, Chlorine, orTechnical Service 6 troubleshootingReplacement Spool OBSERVED FAULT7 warranty information REMINGTON ELECTRIC TRIMMER LIMITED WARRANTYMODELO ST3010A PODADORA ELÉCTRICAMANUAL DEL PROPIETARIO Con doble aislamiento118336 Identificación del producto tabla de contenidosImportante Información sobre la seguridad Ensamble de la podadorabienvenido Modelo Número Fecha de Compra Lugar de Comprao SJTOW-A ADVERTENCIAS DE SEGURIDADANTES DE USAR LA PODADORA Largo delGUARDE ESTAS INSTRUCCIONES MIENTRAS USE LA PODADORAMANTENIMIENTO Y ALMACENAMIENTO DE LA PODADORA Cubierta del Motor 2 identificación del productoEspecificaciones Cubierta del Carrete3 ensamble de la podadora Ensamble de la podadoraSujeción del protector y la rueda de corte Conexión del cordón de extensión 4 operación de la podadoraCordones de extensión Figura 4-4 Método opcional de retención del cordón de extensiónCorte Operación de la podadoraArranque de la podadora Mantenga a los curiosos lejos del área de trabajoCambio de la cuerda de la podadora Avance de la cuerda de la podadoraRetiro del carrete Dirección del paso 4. Mida 30 pies de cuerda de repuestoFigura 4-14 Inserción la cuerda en el orificio derecho de la cuerdaFigura 4-18 Reposición de la tapa del carrete en la carcasa Figura 4-17 Reposición del carrete en la carcasaADVERTENCIACuandolimpie la podadora No la sumerja en ningún líquido 5 mantenimiento de la podadoraLimpieza y mantenimiento No use solventes de limpiezaServicio Técnico 6 análisis de averíasCarrete de repuesto FALLA OBSERVADA7 información sobre la garantía GARANTÍA LIMITADA DE LA PODADORA ELÉCTRICA REMINGTONMODÈLE ST3010A TAILLE-BORDURES ÉLECTRIQUEGUIDE DU PROPRIÉTAIRE Double Isolation118336 Assemblage du taille-bordures Importants renseignements de sécuritéIdentification du produit Utilisation du taille-borduresbienvenue Numéro de modèle Date d’achat Endroit d’achatAVANT D’UTILISER LE TAILLE- BORDURES 1 importants renseignements sur la sécuritéMISES EN GARDE DE SÉCURITÉ LongueurCONSERVEZ CES DIRECTIVES PENDANT L’UTILISATION DU TAILLE-BORDURESENTRETIEN ET ENTREPOSAGE DU TAILLE-BORDURES A. Boîtier du moteur B. Boîtier de la bobine C. Protecteur de coupe 2 identification du produitFiche technique D. Poignée avant E. Poignée arrière F. Cordon électriqueMise en place du protecteur de coupe 3 assemblage du taille-borduresAssemblage du taille-bordures de l’outil4 utilisation du taille-bordures Rallonges électriquesBranchement de la rallonge électrique Utilisation du taille- bordures Démarrage du taille-borduresTaille des bordures Remplacement du fil Rallonge du fil de coupeRetrait de la bobine Figure 4-16 Mise en place du fil dans la bobine ment sur le fil voir la FigureFigure 4-13 Insertion du fil dans l’orifice de gauche Figure 4-15 Tirez fermement sur le filFigure 4-18 Mise en place du couvercle de la bobine sur le boîtier MISE EN GARDE Lors du net- toyage du taille-bordures 5 entretien du taille-borduresEntretien et nettoyage Évitez d’immerger l’appareil dans un liquideSOLUTION Remplacement de la bobineService technique section Remplacement du fil de la7 renseignements sur la garantie GARANTIE LIMITÉE DU TAILLE-BORDURESÉLECTRIQUE REMINGTONMD À DOUBLE ACTION
Top Page Image Contents