Ryobi SS -- RY34440, CS -- RY34420 Troubleshooting, Problem Possible Cause Solution

Page 17

TROUBLESHOOTING

IF THESE SOLUTIONS DO NOT SOLVE THE PROBLEM CONTACT YOUR AUTHORIZED SERVICE DEALER.

PROBLEM

POSSIBLE CAUSE

SOLUTION

Engine will not start

No spark.

Clean or replace spark plug. Reset

 

 

spark plug gap. Refer to Spark Plug

 

 

Replacement earlier in this manual.

 

No fuel.

Push primer bulb until bulb is full of fuel.

 

 

If bulb does not fill, primary fuel delivery

 

 

system is blocked. Contact a service

 

 

dealer. If primer bulb fills, engine may

 

 

be flooded, proceed to next item.

 

Engine is flooded.

Set the start lever to the START position.

 

 

Squeeze the trigger and pull the rope

 

 

repeatedly until the engine starts and

 

 

runs.

 

 

NOTE: Depending on the severity of

 

 

the flooding, this may require numerous

 

 

pulls of the rope.

 

 

 

Engine does not reach full speed and

Air filter screen is dirty.

Clean air filter screen. Refer to Clean-

emits excessive smoke

 

ing Air Filter Screen earlier in this

 

 

manual.

 

Spark arrestor screen is dirty.

Contact a servicing dealer.

 

Spark plug fouled.

Clean or replace spark plug. Reset

 

 

spark plug gap. Refer to Spark Plug

 

 

Replacement earlier in this manual.

 

 

 

Engine starts, runs, and accelerates

Idle speed screw on carburetor needs

Turn idle speed screw clockwise to

but will not idle

adjustment.

increase idle speed. See Figure 28.

 

 

 

Line will not advance

Line is welded to itself.

Replace line. Refer to the applicable line

 

 

replacement section in this manual.

 

Not enough line on spool.

Install more line. Refer to the appli-

 

 

cable line replacement section in this

 

 

manual.

 

Line is worn too short.

Pull lines while alternately pressing

 

 

down on and releasing spool retainer.

 

Line is tangled on spool.

Remove line from spool and rewind.

 

 

Refer to the applicable line replacement

 

 

section in this manual.

 

Engine speed is too slow.

Advance line at full throttle.

 

 

 

Spool retainer hard to turn

Screw threads are dirty or damaged.

Clean threads and lubricate with grease

 

 

- if no improvement, replace the spool

 

 

retainer.

 

 

 

Grass wraps around driveshaft housing

Cutting tall grass at ground level.

Cut tall grass from the top down to

and string head

 

prevent wrapping.

 

Operating trimmer at part throttle.

Operate trimmer at full throttle.

 

 

 

13 — English

Page 16 Page 18
Image 17
Page 16 Page 18
Contents RY34440 Save this Manual for Future ReferenceC430 RY34420 Knob bouton, perilla C430 S430Iii Introduzca LOS Hilos a Través DE LAS Ranuras Hasta QUE Screw vis, tornillo Table of Contents Read all instructions General Safety RulesSymbol Name Specific Safety RulesSymbols Features Attaching the Storage Hanger AssemblyUnpacking Oxygenated Fuels OperationOperating the Trimmer ADDING/checking engine lubricantTo Advance the Cutting line reel easy string head To add engine lubricantStarting and Stopping Cutting TipsGrass Deflector line Trimming CUT-OFF Blade General Maintenance MaintenanceFuel CAP Cleaning the Exhaust Port and Muffler Spark ArrestorStoring the Product Adjusting valve-to-rocker arm clearance­When storing 1 month or longer Ing Air Filter Screen earlier in this TroubleshootingProblem Possible Cause Solution 4050 WarrantySee Adding/Checking Engine Limited Warranty Statement MANUFACTURER’S Warranty Coverage English Lire Toutes LES Instructions Règles DE Sécurité GénéralesRègles DE Sécurité Particulières SymbolesSymbole Nom Caractéristiques Retrait DE L’ACCESSOIRE DU Bloc Moteur Installation DU BLOC-MOTEUR SUR L’ACCESSOIREInstallation DE L’ANNEAU DE Suspension DéballageUtilisation AssemblageUtilisation DU TAILLE-BORDURES AJOUT/VÉRIFICATION DE LubrifiantPour ajouter de l’huile à moteur Pour vérifier le niveau d’huile du moteurDémarrage ET Arrêt Conseils DE CoupeVoir les figures 9 et Voir les figures 12 àInstallation DU FIL Dans LA Tête DE Coupe Reel Easy Installation DE LA Tête DE Coupe Reel EasyInstallation DE LA Tête DE Coupe PRO CUT EntretienNettoyage DU Filtre À AIR Écran Installation DU FIL Dans LA Tête DE Coupe PRO CUTBouchon DU Réservoir Avertissement Changer LE Lubrifiant À MoteurRemisage le produit Ajuster LE Dégagement Entre LA Soupape ET LE CulbuteurVoir les figures 25 Remisage 1 mois ou plusLa figure Problème Cause Possible SolutionDépannage Ajout d’huile à moteur et vérification GarantieÉnoncé DE LA Garantie Limitée Responsabilités DU Propriétaire Dans LE Cadre DE LA Garantie Français Lea todas las instrucciones Reglas DE Seguridad GeneralesAdvertencia Símbolos Reglas DE Seguridad EspecíficasCaracterísticas Desempaquetado ArmadoInstalación DEL Cabezal Motor EN EL Aditamento Montaje DE LA ASA DE ALMACENAMIENTOMontaje DEL Mango Delantero FuncionamientoMontaje DEL Deflector DE Pasto Advertencia Para montar el deflector de pasto del eje curvo C430Para Avanzar EL Hilo DE Corte Cabezal DEL Hilo de reel EasY PrecauciónManejo DE LA Recortadora Cuchilla DE Corte DEL Hilo EN EL Deflector DE Hierba Sugerencias Para CortarArranque Y Apagado Vea las figuras 9 yMantenimiento General MantenimientoInstalación DEL Cabezal DEL Hilo Reel Easy Instalación DEL Hilo EN EL Cabezal DEL Hilo Reel EasyLimpieza DEL Orificio DE Escape Y DEL Silenciador Instalación DEL Hilo EN EL Cabezal DEL Hilo PRO CUTParachispas Tapa DEL Tanque DE Combustible AdvertenciaAlmacenamiento de la producto Ajuste DE LA Apertura DE LA Válvula DEL BalancínAbastecimiento y verificación del lubricante para motor Vea las figuras 25Problema Causa Posible Solución Solución DE ProblemasLa sección Limpieza del filtro de aire Sección Reemplazo de la bujía más arribaEl lubricante para motor en la sección Garantía10w-30. Consulte cómo agregar/verificar Declaración DE LA Garantía Limitada Cobertura DE LA Garantía DEL Fabricante Notas Manuel D’UTILISATION / Manual DEL Operador AVERTISSEMENT 
Top Page Image Contents