Homelite UT80715 Double Insulation, Electrical Connection, Ground Fault Circuit Interrupter

Page 8

SYMBOLS

Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the product better and safer.

SYMBOL

NAME

DESIGNATION/EXPLANATION

 

 

 

 

 

 

V

Volts

Voltage

 

 

 

 

 

 

A

Amperes

Current

 

 

 

 

 

Hz

Hertz

Frequency (cycles per second)

 

 

 

 

 

 

W

Watt

Power

 

 

 

 

 

 

 

 

Alternating Current

Type of current

 

 

 

 

 

no

No Load Speed

Rotational speed, at no load

 

 

 

Class II Construction

Double-insulated construction

 

 

 

.../min

Per Minute

Revolutions, strokes, surface speed, orbits etc., per minute

ELECTRICAL

DOUBLE INSULATION

Double insulation is a concept in safety in electric power tools, which eliminates the need for the usual three- wire grounded power cord. All exposed metal parts are isolated from the internal metal motor components with protecting insulation. Double insulated products do not need to be grounded.

WARNING:

The double insulated system is intended­ to protect the user from shock resulting from a break in the product’s internal insulation. Observe all normal safety precautions to avoid electrical shock.

NOTE: Servicing of a product with double insulation requires extreme care and knowledge of the system and should be performed only by a qualified service technician. For service, we suggest you return the product to your nearest authorized service center for repair. Always use original factory replace- ment parts when servicing.

ELECTRICAL CONNECTION

This product has a precision-built electric motor. It should be connected to a power supply that is 120 volts, AC only (normal household current), 60 Hz. Do not operate this product on direct current (DC). A substantial voltage drop will cause a loss of power and the motor will overheat. If the product does not operate when plugged into an outlet, double-check the power supply.

GROUND FAULT CIRCUIT INTERRUPTER

See Figure 1.

This unit is equipped with a Ground Fault Circuit Interrupter (GFCI), which guards against the hazards of ground fault currents. An example of ground fault current is the current that would flow through a person who is using an appliance with faulty insulation and, at the same time, is in contact with an electrical ground such as a plumbing fixture, wet floor, or earth.

GFCI plugs do not protect against short circuits, overloads, or shocks.

NOTE: After the unit is connected to a power source, it is ready for use. It is not necessary to press the reset button before initial start up.

The GFCI plug can be tested with the TEST and RESET buttons.

To test:

Depress the TEST button. This should cause the RESET button to pop out.

To restore power, depress the RESET button.

Perform this test monthly to ensure proper operation of the GFCI.

6 — English

Image 8
Contents OPERATOR’S Manual Save this Manual for Future ReferenceGancho y lazada Iii Table of Contents IntroductionImportant Safety Instructions Read ALL Instructions Before Using this ProductGround Fault Circuit Interrupter Protection Servicing of a DOUBLE-INSULATED ApplianceSpecific Safety Rules Symbols Symbol Signal MeaningGround Fault Circuit Interrupter ElectricalDouble Insulation Electrical ConnectionFeatures AssemblyConnecting the Water Supply to the Pressure Washer Connecting the High Pressure Hose to the PumpUsing the Spray Wand AS a Handle Connecting High Pressure Hose to Trigger HandleUsing the Spray Wand Trigger OperationApplications Adding Detergent to the Pressure WasherUsing the Nozzles Using the High Pressure HoseUsing the Cleaning Deck Operating the Pressure WasherMaintenance General MaintenanceNozzle Maintenance Moving the Pressure WASHER­Cleaning the Deck Nozzles To clean nozzlesChanging the High Pressure Filter Storing the Pressure WasherTroubleshooting Problem Possible Cause SolutionWarranty Limited Warranty StatementInstructions Importantes Concernant LA Sécurité Conserver CES InstructionsRègles DE Sécurité Particulières Symboles Symbole Signal SignificationCaractéristiques Électriques Isolation DoubleDisjoncteur DE Fuite À LA Terre Connexion ÉlectriqueCaractéristiques AssemblageConnexion DU Tuyau Haute Pression SUR LA Pompe Assemblage DE LA Lance DE PulvérisationUtilisation DE LA Lance D’ARROSAGE Comme Poignée Connexion DU Tuyau Haute Pression À Poignée DE GâchetteUtilisation Ajout DE Détergent Dans LA Laveuse À PressionMise EN Marche / Arrêt DU Nettoyeur Haute Pression Fonctionnement Poignée DE GâchetteFonctionnement LES Buses Utilisation DU Tuyau Haute PressionUtilisation LA Nettoyeur Haute Pression Pour engager le verrouillage Déplacement DU Nettoyeur Haute Pression EntretienUtiliser DE Pont DE Nettoyer Entretien GénéralEntretien DE Buse Pour Nettoyer LE Buse À PontChangement DU Filtre Haute Pression Remisage DU Nettoyeur Haute PressionProblème Cause Possible Solution DépannageGarantie Énoncé DE LA Garantie Limitée Hors MoteurInstrucciones DE Seguridad Importantes Guarde Estas InstruccionesAdvertencia LEA Todas LAS Instrucciones Antes DE Usar Este ProductoReglas DE Seguridad Específicas Precaución SímbolosPeligro Aspectos Eléctricos Doble AislamientoConexión Eléctrica Vea la figuraCaracterísticas ArmadoUtilizar DEL Tubo Rociador Como LA Mango Cómo Conectar LA Manguera DE Alta Presión a LA BombaArmado DEL Tubo Rociador Funcionamiento Encendido Y Apagado DE LA Lavadora DE PresiónUsos Agregado DE Detergente a LA Lavadora DE PresiónAccionamiento DE LA Lavadora DE Presión USO LAS BoquillasUSO DE LA Manguera DE Alta Presión Mantenimiento USO DE LA Unidad DE LimpiezaCómo Mover LA Lavadora a Presión Mantenimiento GeneralMantenimiento DE LAS Boquillas Mantenimiento DE LAS Boquillas DE LA UnidadLimpieza DEL Filtro DE Alta Presión Guardado DE LA Lavadora DE PresiónSolución DE Problemas Problema Causa Posible SoluciónGarantía Declaración DE Garantía Limitada CON Excepción DEL MotorPage AVERTISSEMENT  OPERATOR’S ManualManuel D’UTILISATION Manual DEL Operador