Agilent Technologies E4400-90333 manual Data out of range value clipped to upper limit

Page 33

ESG Family Signal Generators

-299 to -200: Execution Errors

Data out of range; value clipped to upper limit.

An input value is above the maximum value allowed. Examples: frequency setting, reference, or offset; output power; power reference and offset; modulation depth, deviation, or modulation source frequency; number of points and start/stop values for list mode; start/stop values for internal I/Q calibration; sequence or register values (save/recall); dwell time.

-221Settings conflict

A legal program data element was parsed but could not be executed due to the current device state (see IEEE 488.2 11.5.1.1.5).

Settings conflict; At least one of the channels must be on in order to turn the mode on. CDMA2000 has been turned off.

To output a valid RF signal, at least one channel must be turned on. Since all channels are off, CDMA2000 mode has been turned off to avoid undeﬁned behavior.

Settings conflict; At least one of the channels must be on in order to turn the mode on. WCDMA has been turned off.

To output a valid RF signal, at least one channel must be turned on. Since all channels are off, W-CDMA mode has been turned off to avoid undeﬁned behavior.

Settings conflict; BBG Data Clock is fixed to EXTernal to synchronize Data Gen to Demodulator.

With both the GSM format and the BERT GSM activated, an attempt was made to toggle the baseband data clock from external to internal. The baseband data clock is ﬁxed to external in order to synchronize the data generator to the demodulator.

Settings conflict; Cannot have a secondary frame with a non-framed data pattern. The secondary frame is unchanged.

The secondary frame feature has many potential conﬂicts. Some of the conﬂicts leave the secondary pattern and its state as they were prior to the command that led to the error message, and some turn off the secondary state, since the primary state is not compatible and it has priority.

Settings conflict; Cannot have a secondary frame with all timeslots off. The secondary frame is unchanged.

The secondary frame feature has many potential conﬂicts. Some of the conﬂicts leave the secondary pattern and its state as they were prior to the command that led to the error message, and some turn off the secondary state, since the primary state is not compatible and it has priority.

Error Messages

31

Image 33

Contents Supersedes February Copyright 1999-2001 Agilent Technologies Afﬁx Label Here Part No. E4400-90333Contents Introduction Error Message Format Error Message Types No Error To -400 Query Errors Device has detected a failure during its self-test procedure To -300 Device-Speciﬁc ErrorsSelf-test for a particular power supply voltage has failed. Nearest Agilent Technologies sales or service ofﬁceBurst generator memory failed. Modulation data produced by 321Out of memory ARB communication failed Out of memory Could not copy current istate Out of memory Histogram display cannot function Out of memory Memory allocation error Out of memory Object Memory Area Instrument is still functional Lost. The meaning of this error is device-dependent320 315Protected user data saved by the *PUD command has been lost Non-volatile data saved by the *SAV? command has been lostAn error was detected in the device’s memory ValuesSystem error File Not Found To -200 Execution Errors 285 When parsing a downloaded program is device-speciﬁc284 IllegalDue to an error within the macro deﬁnition see Ieee 488.2 Command header, or contained invalid header syntaxAttempted. The deﬁnition of a math error is device-speciﬁc 276An illegal memory subsystem name was used after the @ ﬁlename of was speciﬁed. This is not a legal ﬁlenameFile name error Illegal filename character File name not found SYSTEMFCDMA2KCHANFILE Deﬁnition of what constitutes full media is device-speciﬁc 254Catalog. Afterwards, try again Try again252 Sales or service ofﬁceWhat constitutes missing media is device-speciﬁc 250Measurement accuracy is questionable Data corrupt or stale filename Algorithm. a potential cause is a failing backup battery During the ﬁrst power up after downloading new ﬁrmware intoEeprom master copy if one exists. The system automatically 226Memory or related device-speciﬁc requirements 223To -200 Execution Errors Too much data User filter has too many symbols Data out of range Synthesizer Frequency out of bounds Data out of range value clipped to upper limit To -200 Execution Errors All digital modulation multicarriers must be the same format To -200 Execution Errors ESG Family Signal Generators Settings conflict Edge Bert requires Normal as Timeslot Type Settings conflict FM & PM not allowed Settings conflict GSM Bert requires Normal as Timeslot Type ESG Family Signal Generators Settings conflict I/Q & AM WB cannot be on at the same time ESG Family Signal Generators To -200 Execution Errors Used in RC3 and 4 for channel Used in RC1To -200 Execution Errors ESG Family Signal Generators Error For errors -221 throughManual mode is on and therefore the instrument cannot sweep 220212 Have described the error that is stalling list/sweepIgnored 211Execution Error Cannot update FlexDG with Even Second Delay To -100 Command Errors Speciﬁed ﬁlename exceeds the maximum length Detect a more speciﬁc error Device cannot detect a more speciﬁc error150 148Header contains more than twelve characters see Ieee 488.2 110Command header error Syntax error Invalid ﬁle name 201 to 702 Device-Speciﬁc ErrorsUser has attempted to write to a read-only memory subsystem State ﬁle is not readable and the recall was abortedSynthesizer is unlocked. Service may be needed Internal error report to factoryInstrument’s output is unleveled 513 1 GHz Oscillator unlocked Calibration failure Dcfm DC overrange Reverse Power Protection RPP Tripped DSP FW download failed Demodulator board DSP times out Demodulator communication failed Option 300 DSP for Bert capability returns an error Configuration Error Option reconfiguration failed Configuration error Installed board not supported Configuration error OPTION, Invalid inconsistent license key Option UN7 hardware has an invalid revision of Fpga code Demodulator board has an invalid revision of DSP boot codeFpga download failed Demodulator board Modulation must have at least two states speciﬁed ﬁlter must have at least one coefﬁcient speciﬁedBurst shape ﬁle is corrupted, or is not in the proper format ﬁle is either corrupt or is not a FIR ﬁle