Agilent Technologies E4400-90333 manual Settings conflict FM & PM not allowed

Page 39

ESG Family Signal Generators

-299 to -200: Execution Errors

Settings conflict; FM2/PM2 value set greater than FM1/PM1 value. FM1/PM1 changed to match FM2/PM2 value.

FM2/PM2 deviation must be FM1/PM1 deviation. This error is reported when both FM1/PM1 and FM2/PM2 are enabled and an adjustment to either FM2/PM2 deviation causes the FM2 or PM2 deviation to be greater than the FM1 or PM1 deviation. It is also be reported as FM2/PM2 is turned on, and the last FM1/PM1 deviation setting is less than the current FM2/PM2 deviation setting. In both cases the FM1/PM1 deviation is adjusted to match the FM2/PM2 deviation.

Settings conflict; FM & PM not allowed.

There is a hardware conﬂict between FM and PM. The most recently requested modulation will be turned on, the previous modulation will be turned off.

Settings conflict; The format must be on and fully configured for use before being specified as the secondary frame. The secondary frame is unchanged.

The secondary frame setup must be completely conﬁgured as a stand-alone setup before being selected for use as a secondary frame. It must have a format, framing, and at least one timeslot turned on.

Settings conflict; Frame in Pattern RAM is from a different format. The secondary frame is unchanged.

The secondary frame feature has many potential conﬂicts. Some of the conﬂicts leave the secondary pattern and its state as they were prior to the command that led to the error message, and some turn off the secondary state, since the primary state is not compatible and it has priority.

Settings conflict; Frame repeat changed to continuous.

Single is not a valid repeat setting for an external data source.

Settings conflict; Frequency list and dwell list are of unequal size. Set one list equal to size one, or make their sizes equal.

The frequency list has more than one element and the dwell list has more than one element, and they are not of equal size. If any of the frequency, power, or dwell lists have more than one element, they must all have the same number of elements. A list of a single element is the same as a list of an equal size with the single element repeated the necessary number of times.

Error Messages

37

Image 39

Contents Supersedes February Copyright 1999-2001 Agilent Technologies Afﬁx Label Here Part No. E4400-90333Contents Introduction Error Message Format Error Message Types No Error To -400 Query Errors Device has detected a failure during its self-test procedure To -300 Device-Speciﬁc Errors321 Nearest Agilent Technologies sales or service ofﬁceSelf-test for a particular power supply voltage has failed. Burst generator memory failed. Modulation data produced byOut of memory ARB communication failed Out of memory Could not copy current istate Out of memory Histogram display cannot function Out of memory Memory allocation error Out of memory Object Memory Area 315 Lost. The meaning of this error is device-dependentInstrument is still functional 320Values Non-volatile data saved by the *SAV? command has been lostProtected user data saved by the *PUD command has been lost An error was detected in the device’s memorySystem error File Not Found To -200 Execution Errors Illegal When parsing a downloaded program is device-speciﬁc285 284276 Command header, or contained invalid header syntaxDue to an error within the macro deﬁnition see Ieee 488.2 Attempted. The deﬁnition of a math error is device-speciﬁcAn illegal memory subsystem name was used after the @ ﬁlename of was speciﬁed. This is not a legal ﬁlenameFile name error Illegal filename character File name not found SYSTEMFCDMA2KCHANFILE Try again 254Deﬁnition of what constitutes full media is device-speciﬁc Catalog. Afterwards, try again250 Sales or service ofﬁce252 What constitutes missing media is device-speciﬁcMeasurement accuracy is questionable Data corrupt or stale filename 226 During the ﬁrst power up after downloading new ﬁrmware intoAlgorithm. a potential cause is a failing backup battery Eeprom master copy if one exists. The system automaticallyMemory or related device-speciﬁc requirements 223To -200 Execution Errors Too much data User filter has too many symbols Data out of range Synthesizer Frequency out of bounds Data out of range value clipped to upper limit To -200 Execution Errors All digital modulation multicarriers must be the same format To -200 Execution Errors ESG Family Signal Generators Settings conflict Edge Bert requires Normal as Timeslot Type Settings conflict FM & PM not allowed Settings conflict GSM Bert requires Normal as Timeslot Type ESG Family Signal Generators Settings conflict I/Q & AM WB cannot be on at the same time ESG Family Signal Generators To -200 Execution Errors Used in RC3 and 4 for channel Used in RC1To -200 Execution Errors ESG Family Signal Generators 220 For errors -221 throughError Manual mode is on and therefore the instrument cannot sweep211 Have described the error that is stalling list/sweep212 IgnoredExecution Error Cannot update FlexDG with Even Second Delay To -100 Command Errors Speciﬁed ﬁlename exceeds the maximum length 148 Device cannot detect a more speciﬁc errorDetect a more speciﬁc error 150Header contains more than twelve characters see Ieee 488.2 110Command header error Syntax error Invalid ﬁle name 201 to 702 Device-Speciﬁc ErrorsUser has attempted to write to a read-only memory subsystem State ﬁle is not readable and the recall was abortedSynthesizer is unlocked. Service may be needed Internal error report to factoryInstrument’s output is unleveled 513 1 GHz Oscillator unlocked Calibration failure Dcfm DC overrange Reverse Power Protection RPP Tripped DSP FW download failed Demodulator board DSP times out Demodulator communication failed Option 300 DSP for Bert capability returns an error Configuration Error Option reconfiguration failed Configuration error Installed board not supported Configuration error OPTION, Invalid inconsistent license key Option UN7 hardware has an invalid revision of Fpga code Demodulator board has an invalid revision of DSP boot codeFpga download failed Demodulator board Modulation must have at least two states speciﬁed ﬁlter must have at least one coefﬁcient speciﬁedBurst shape ﬁle is corrupted, or is not in the proper format ﬁle is either corrupt or is not a FIR ﬁle