Agilent Technologies E4400-90333 manual Configuration error Installed board not supported

Page 67

ESG Family Signal Generators

201 to 702: Device-Speciﬁc Errors

Configuration error; Installed board not supported.

An option board or board combination that is not supported by the installed ﬁrmware has been speciﬁed or detected. Be sure that you have the proper instrument and ﬁrmware to support the option board, and that you have speciﬁed a supported combination of options.

Configuration error; Invalid Data Generator memory configuration.

The memory conﬁguration for an option board does not match the known memory limits of any supported option board. If this error has occurred as the result of a customer-installed option, uninstall all options and then reinstall the correct options. Report this error to the nearest

Agilent Technologies sales or service ofﬁce.

Configuration error; Invalid file system configuration block size defaulted.

A block size conﬁguration error was detected by the ﬁle system. A default value has been used. Report this error to the nearest Agilent Technologies sales or service ofﬁce.

Configuration error; Invalid file system configuration max files defaulted.

A maximum ﬁles conﬁguration error was detected by the ﬁle system. A default value has been used. Report this error to the nearest Agilent Technologies sales or service ofﬁce.

Configuration error; Invalid file system configuration memory size defaulted.

A memory size conﬁguration error was detected by the ﬁle system. A default value has been used. Report this error to the nearest Agilent Technologies sales or service ofﬁce.

Configuration error; Invalid option board configuration.

An invalid combination of option boards has been conﬁgured. If this error has occurred as the result of a customer-installed option, uninstall all options and then reinstall the correct options. Report this error to the nearest Agilent Technologies sales or service ofﬁce.

Error Messages

65

Image 67

Contents Supersedes February Copyright 1999-2001 Agilent Technologies Afﬁx Label Here Part No. E4400-90333Contents Introduction Error Message Format Error Message Types No Error To -400 Query Errors Device has detected a failure during its self-test procedure To -300 Device-Speciﬁc Errors321 Nearest Agilent Technologies sales or service ofﬁceSelf-test for a particular power supply voltage has failed. Burst generator memory failed. Modulation data produced byOut of memory ARB communication failed Out of memory Could not copy current istate Out of memory Histogram display cannot function Out of memory Memory allocation error Out of memory Object Memory Area 315 Lost. The meaning of this error is device-dependentInstrument is still functional 320Values Non-volatile data saved by the *SAV? command has been lostProtected user data saved by the *PUD command has been lost An error was detected in the device’s memorySystem error File Not Found To -200 Execution Errors Illegal When parsing a downloaded program is device-speciﬁc285 284276 Command header, or contained invalid header syntaxDue to an error within the macro deﬁnition see Ieee 488.2 Attempted. The deﬁnition of a math error is device-speciﬁcAn illegal memory subsystem name was used after the @ ﬁlename of was speciﬁed. This is not a legal ﬁlenameFile name error Illegal filename character File name not found SYSTEMFCDMA2KCHANFILE Try again 254Deﬁnition of what constitutes full media is device-speciﬁc Catalog. Afterwards, try again250 Sales or service ofﬁce252 What constitutes missing media is device-speciﬁcMeasurement accuracy is questionable Data corrupt or stale filename 226 During the ﬁrst power up after downloading new ﬁrmware intoAlgorithm. a potential cause is a failing backup battery Eeprom master copy if one exists. The system automaticallyMemory or related device-speciﬁc requirements 223To -200 Execution Errors Too much data User filter has too many symbols Data out of range Synthesizer Frequency out of bounds Data out of range value clipped to upper limit To -200 Execution Errors All digital modulation multicarriers must be the same format To -200 Execution Errors ESG Family Signal Generators Settings conflict Edge Bert requires Normal as Timeslot Type Settings conflict FM & PM not allowed Settings conflict GSM Bert requires Normal as Timeslot Type ESG Family Signal Generators Settings conflict I/Q & AM WB cannot be on at the same time ESG Family Signal Generators To -200 Execution Errors Used in RC3 and 4 for channel Used in RC1To -200 Execution Errors ESG Family Signal Generators 220 For errors -221 throughError Manual mode is on and therefore the instrument cannot sweep211 Have described the error that is stalling list/sweep212 IgnoredExecution Error Cannot update FlexDG with Even Second Delay To -100 Command Errors Speciﬁed ﬁlename exceeds the maximum length 148 Device cannot detect a more speciﬁc errorDetect a more speciﬁc error 150Header contains more than twelve characters see Ieee 488.2 110Command header error Syntax error Invalid ﬁle name 201 to 702 Device-Speciﬁc ErrorsUser has attempted to write to a read-only memory subsystem State ﬁle is not readable and the recall was abortedInternal error report to factory Synthesizer is unlocked. Service may be neededInstrument’s output is unleveled 513 1 GHz Oscillator unlocked Calibration failure Dcfm DC overrange Reverse Power Protection RPP Tripped DSP FW download failed Demodulator board DSP times out Demodulator communication failed Option 300 DSP for Bert capability returns an error Configuration Error Option reconfiguration failed Configuration error Installed board not supported Configuration error OPTION, Invalid inconsistent license key Option UN7 hardware has an invalid revision of Fpga code Demodulator board has an invalid revision of DSP boot codeFpga download failed Demodulator board Modulation must have at least two states speciﬁed ﬁlter must have at least one coefﬁcient speciﬁedBurst shape ﬁle is corrupted, or is not in the proper format ﬁle is either corrupt or is not a FIR ﬁle