Agilent Technologies E4400-90333 manual Calibration failure Dcfm DC overrange

Page 61

ESG Family Signal Generators

201 to 702: Device-Speciﬁc Errors

Calibration failure; DCFM DC overrange

The instrument was unable to perform a DCFM or DCΦM calibration due to the input signal being outside of the offset range that can be calibrated for.

Calibration failure; I/Q cal.

While executing the internal I/Q calibration, the attempt to allocate memory for the calibration failed.

Calibration failure; I/Q cal failed to allocate memory.

While executing the internal I/Q calibration, a failure occurred during the section indicated.

Calibration failure; ‘Marble Cal’, ‘Offset Cal’, ‘Other Cal’, ‘Gain Cal’, ‘BBG Cal’, ‘ARB Cal’

While executing the internal I/Q calibration, a failure occurred during the section indicated.

Calibration failure; Upgrade calibration failed. Data not stored.

The calibration stage of the instrument upgrade was not executed successfully. The calibration data has not been stored. The upgrade is not functional. Report this error to the nearest Agilent Technologies sales or service ofﬁce.

518Arbitrary Waveform Generator unlocked; refer to manual.

The instrument’s dual arbitrary waveform generator is unlocked. This error will occur when the ARB Reference key is set to Ext and there is no external signal applied to the instrument. It may also occur if there is a problem with the A5 dual arbitrary waveform generator board.

519Uncalibrated signal; IQ Adjustments not calibrated. Refer to manual.

A calibration is required to use the IQ adjustments feature. The I/Q adjustments may be functional, but are not guaranteed to meet speciﬁcations until an I/Q calibration is performed. Refer to the user’s guide.

Error Messages

59

Image 61

Contents Supersedes February Copyright 1999-2001 Agilent Technologies Afﬁx Label Here Part No. E4400-90333Contents Introduction Error Message Format Error Message Types No Error To -400 Query Errors Device has detected a failure during its self-test procedure To -300 Device-Speciﬁc ErrorsSelf-test for a particular power supply voltage has failed. Nearest Agilent Technologies sales or service ofﬁceBurst generator memory failed. Modulation data produced by 321Out of memory ARB communication failed Out of memory Could not copy current istate Out of memory Histogram display cannot function Out of memory Memory allocation error Out of memory Object Memory Area Instrument is still functional Lost. The meaning of this error is device-dependent320 315Protected user data saved by the *PUD command has been lost Non-volatile data saved by the *SAV? command has been lostAn error was detected in the device’s memory ValuesSystem error File Not Found To -200 Execution Errors 285 When parsing a downloaded program is device-speciﬁc284 IllegalDue to an error within the macro deﬁnition see Ieee 488.2 Command header, or contained invalid header syntaxAttempted. The deﬁnition of a math error is device-speciﬁc 276An illegal memory subsystem name was used after the @ ﬁlename of was speciﬁed. This is not a legal ﬁlenameFile name error Illegal filename character File name not found SYSTEMFCDMA2KCHANFILE Deﬁnition of what constitutes full media is device-speciﬁc 254Catalog. Afterwards, try again Try again252 Sales or service ofﬁceWhat constitutes missing media is device-speciﬁc 250Measurement accuracy is questionable Data corrupt or stale filename Algorithm. a potential cause is a failing backup battery During the ﬁrst power up after downloading new ﬁrmware intoEeprom master copy if one exists. The system automatically 226Memory or related device-speciﬁc requirements 223To -200 Execution Errors Too much data User filter has too many symbols Data out of range Synthesizer Frequency out of bounds Data out of range value clipped to upper limit To -200 Execution Errors All digital modulation multicarriers must be the same format To -200 Execution Errors ESG Family Signal Generators Settings conflict Edge Bert requires Normal as Timeslot Type Settings conflict FM & PM not allowed Settings conflict GSM Bert requires Normal as Timeslot Type ESG Family Signal Generators Settings conflict I/Q & AM WB cannot be on at the same time ESG Family Signal Generators To -200 Execution Errors Used in RC3 and 4 for channel Used in RC1To -200 Execution Errors ESG Family Signal Generators Error For errors -221 throughManual mode is on and therefore the instrument cannot sweep 220212 Have described the error that is stalling list/sweepIgnored 211Execution Error Cannot update FlexDG with Even Second Delay To -100 Command Errors Speciﬁed ﬁlename exceeds the maximum length Detect a more speciﬁc error Device cannot detect a more speciﬁc error150 148Header contains more than twelve characters see Ieee 488.2 110Command header error Syntax error Invalid ﬁle name 201 to 702 Device-Speciﬁc ErrorsUser has attempted to write to a read-only memory subsystem State ﬁle is not readable and the recall was abortedInternal error report to factory Synthesizer is unlocked. Service may be neededInstrument’s output is unleveled 513 1 GHz Oscillator unlocked Calibration failure Dcfm DC overrange Reverse Power Protection RPP Tripped DSP FW download failed Demodulator board DSP times out Demodulator communication failed Option 300 DSP for Bert capability returns an error Configuration Error Option reconfiguration failed Configuration error Installed board not supported Configuration error OPTION, Invalid inconsistent license key Option UN7 hardware has an invalid revision of Fpga code Demodulator board has an invalid revision of DSP boot codeFpga download failed Demodulator board Modulation must have at least two states speciﬁed ﬁlter must have at least one coefﬁcient speciﬁedBurst shape ﬁle is corrupted, or is not in the proper format ﬁle is either corrupt or is not a FIR ﬁle