Agilent Technologies E4400-90333 manual DSP times out Demodulator communication failed

Page 64

201 to 702: Device-Specific Errors

ESG Family Signal Generators

DSP times out; Demodulator communication failed

The digital signal processor (DSP) on the Demodulator board (Option 300) failed to respond within the appropriate amount of time. If cycling power does not correct the problem, report this error to the nearest

Agilent Technologies sales or service office.

DSP times out; FlexDG communication failed

The instrument is unable to communicate with the FLEXDG data generator board. The baseband generator can not function.

DSP times out; FPGA download failed: DUAL ARB BOARD

The initialization of hardware necessary for the operation of the dual arbitrary waveform generator (Option UND) failed. The dual arbitrary waveform generator is not functional. Report this error to the nearest Agilent Technologies sales or service office.

DSP times out; Option 300 BERT capability

The digital signal processor (DSP) on the bit error rate tester board failed to respond while Option 300 is operating. Report this error to the nearest Agilent Technologies sales or service office.

607DSP returns error.

The digital signal processor (DSP) is in an indeterminate state. Report this error to the nearest Agilent Technologies sales or service office.

DSP returns error; ARB address line error (code)

The dual arbitrary waveform generator (Option UND) digital signal processor (DSP) detected an internal error when processing a command. The DSP specific error code is displayed in the parenthesis. Report this error to the nearest Agilent Technologies sales or service office.

DSP returns error; ARB Command not recognized (code)

The dual arbitrary waveform generator (Option UND) digital signal processor (DSP) detected a communications error with the command sent to it. The DSP specific error code is displayed in the parenthesis. Report this error to the nearest Agilent Technologies sales or service office.

DSP returns error; ARB communications failed. (code)

The dual arbitrary waveform generator (Option UND) digital signal processor (DSP) detected an error and it is in an indeterminate state. The DSP specific error code is displayed in the parenthesis. Report this error to the nearest Agilent Technologies sales or service office.

62

Error Messages

Image 64
Contents Affix Label Here Part No. E4400-90333 Supersedes February Copyright 1999-2001 Agilent TechnologiesContents Introduction Error Message Format Error Message Types No Error To -400 Query Errors To -300 Device-Specific Errors Device has detected a failure during its self-test procedureNearest Agilent Technologies sales or service office Self-test for a particular power supply voltage has failed.Burst generator memory failed. Modulation data produced by 321Out of memory ARB communication failed Out of memory Could not copy current istate Out of memory Histogram display cannot function Out of memory Memory allocation error Out of memory Object Memory Area Lost. The meaning of this error is device-dependent Instrument is still functional320 315Non-volatile data saved by the *SAV? command has been lost Protected user data saved by the *PUD command has been lostAn error was detected in the device’s memory ValuesSystem error File Not Found To -200 Execution Errors When parsing a downloaded program is device-specific 285284 IllegalCommand header, or contained invalid header syntax Due to an error within the macro definition see Ieee 488.2Attempted. The definition of a math error is device-specific 276filename of was specified. This is not a legal filename An illegal memory subsystem name was used after the @File name error Illegal filename character File name not found SYSTEMFCDMA2KCHANFILE 254 Definition of what constitutes full media is device-specificCatalog. Afterwards, try again Try againSales or service office 252What constitutes missing media is device-specific 250Measurement accuracy is questionable Data corrupt or stale filename During the first power up after downloading new firmware into Algorithm. a potential cause is a failing backup batteryEeprom master copy if one exists. The system automatically 226223 Memory or related device-specific requirementsTo -200 Execution Errors Too much data User filter has too many symbols Data out of range Synthesizer Frequency out of bounds Data out of range value clipped to upper limit To -200 Execution Errors All digital modulation multicarriers must be the same format To -200 Execution Errors ESG Family Signal Generators Settings conflict Edge Bert requires Normal as Timeslot Type Settings conflict FM & PM not allowed Settings conflict GSM Bert requires Normal as Timeslot Type ESG Family Signal Generators Settings conflict I/Q & AM WB cannot be on at the same time ESG Family Signal Generators To -200 Execution Errors Used in RC1 Used in RC3 and 4 for channelTo -200 Execution Errors ESG Family Signal Generators For errors -221 through ErrorManual mode is on and therefore the instrument cannot sweep 220Have described the error that is stalling list/sweep 212Ignored 211Execution Error Cannot update FlexDG with Even Second Delay To -100 Command Errors Specified filename exceeds the maximum length Device cannot detect a more specific error Detect a more specific error150 148Header contains more than twelve characters see Ieee 488.2 110Command header error Syntax error 201 to 702 Device-Specific Errors Invalid file nameState file is not readable and the recall was aborted User has attempted to write to a read-only memory subsystemInternal error report to factory Synthesizer is unlocked. Service may be neededInstrument’s output is unleveled 513 1 GHz Oscillator unlocked Calibration failure Dcfm DC overrange Reverse Power Protection RPP Tripped DSP FW download failed Demodulator board DSP times out Demodulator communication failed Option 300 DSP for Bert capability returns an error Configuration Error Option reconfiguration failed Configuration error Installed board not supported Configuration error OPTION, Invalid inconsistent license key Demodulator board has an invalid revision of DSP boot code Option UN7 hardware has an invalid revision of Fpga codeFpga download failed Demodulator board filter must have at least one coefficient specified Modulation must have at least two states specifiedfile is either corrupt or is not a FIR file Burst shape file is corrupted, or is not in the proper format