Agilent Technologies E4400-90333 manual ESG Family Signal Generators

Page 37

ESG Family Signal Generators

-299 to -200: Execution Errors

Settings conflict; Continuous & Discontinuous setting conflict. All selected Continuous timeslots are now switched to Discontinuous.

Indicates that while in TETRA mode, an attempt has been made to simultaneously assign continuous and discontinuous protocols to the timeslots. Continuous and discontinuous protocols cannot coexist in TETRA mode. If a discontinuous protocol is selected for any timeslot, all timeslots’ protocols are changed to discontinuous protocols.

Settings conflict; Current frame length does not have symbol boundary. End of frame has been patched with extra bits to allow an integer of symbols in a frame.

With Option UN8, in TDMA format you can select from many different modulations with different bits per symbol. Because all TDMA formats have a ﬁxed frame size, in some modulations end-of-frame and end-of-symbol do not happen at the same time. This message indicates that end-of-frame has been patched with extra bits to allow an integer of symbols per frame.

Settings conflict; Discontinuous & Continuous setting conflict. All selected Discontinuous timeslots are now switched to Continuous.

Indicates that while in TETRA mode, an attempt has been made to simultaneously assign discontinuous and continuous protocols to the timeslots. Discontinuous and continuous protocols cannot coexist in TETRA mode. If a continuous protocol is selected for any timeslot, all timeslots’ protocols are changed to continuous protocols.

Settings conflict; Downlink & Uplink setting conflict. All selected Downlink timeslots are now set to Uplink.

A Downlink timeslot type has been selected while another timeslot(s) has Uplink selected. In NADC and PDC digital modulation for bursted data, only either Uplink (base to mobile) or Downlink (mobile to base) Trafﬁc Channel type can be selected for all timeslots at any one moment.To continue data transmission, all Downlink timeslots have been changed to the Uplink conﬁguration.

Settings conflict; EDGE BERT requires Multiframe PN Sequence in Timeslot E field.

An unsupported data type was encountered. The measurement timeslot requires a multiframe PN sequence in the E ﬁeld.

Error Messages

35

Image 37

Contents Supersedes February Copyright 1999-2001 Agilent Technologies Afﬁx Label Here Part No. E4400-90333Contents Introduction Error Message Format Error Message Types No Error To -400 Query Errors Device has detected a failure during its self-test procedure To -300 Device-Speciﬁc ErrorsSelf-test for a particular power supply voltage has failed. Nearest Agilent Technologies sales or service ofﬁceBurst generator memory failed. Modulation data produced by 321Out of memory ARB communication failed Out of memory Could not copy current istate Out of memory Histogram display cannot function Out of memory Memory allocation error Out of memory Object Memory Area Instrument is still functional Lost. The meaning of this error is device-dependent320 315Protected user data saved by the *PUD command has been lost Non-volatile data saved by the *SAV? command has been lostAn error was detected in the device’s memory ValuesSystem error File Not Found To -200 Execution Errors 285 When parsing a downloaded program is device-speciﬁc284 IllegalDue to an error within the macro deﬁnition see Ieee 488.2 Command header, or contained invalid header syntaxAttempted. The deﬁnition of a math error is device-speciﬁc 276An illegal memory subsystem name was used after the @ ﬁlename of was speciﬁed. This is not a legal ﬁlenameFile name error Illegal filename character File name not found SYSTEMFCDMA2KCHANFILE Deﬁnition of what constitutes full media is device-speciﬁc 254Catalog. Afterwards, try again Try again252 Sales or service ofﬁceWhat constitutes missing media is device-speciﬁc 250Measurement accuracy is questionable Data corrupt or stale filename Algorithm. a potential cause is a failing backup battery During the ﬁrst power up after downloading new ﬁrmware intoEeprom master copy if one exists. The system automatically 226Memory or related device-speciﬁc requirements 223To -200 Execution Errors Too much data User filter has too many symbols Data out of range Synthesizer Frequency out of bounds Data out of range value clipped to upper limit To -200 Execution Errors All digital modulation multicarriers must be the same format To -200 Execution Errors ESG Family Signal Generators Settings conflict Edge Bert requires Normal as Timeslot Type Settings conflict FM & PM not allowed Settings conflict GSM Bert requires Normal as Timeslot Type ESG Family Signal Generators Settings conflict I/Q & AM WB cannot be on at the same time ESG Family Signal Generators To -200 Execution Errors Used in RC3 and 4 for channel Used in RC1To -200 Execution Errors ESG Family Signal Generators Error For errors -221 throughManual mode is on and therefore the instrument cannot sweep 220212 Have described the error that is stalling list/sweepIgnored 211Execution Error Cannot update FlexDG with Even Second Delay To -100 Command Errors Speciﬁed ﬁlename exceeds the maximum length Detect a more speciﬁc error Device cannot detect a more speciﬁc error150 148Header contains more than twelve characters see Ieee 488.2 110Command header error Syntax error Invalid ﬁle name 201 to 702 Device-Speciﬁc ErrorsUser has attempted to write to a read-only memory subsystem State ﬁle is not readable and the recall was abortedInternal error report to factory Synthesizer is unlocked. Service may be neededInstrument’s output is unleveled 513 1 GHz Oscillator unlocked Calibration failure Dcfm DC overrange Reverse Power Protection RPP Tripped DSP FW download failed Demodulator board DSP times out Demodulator communication failed Option 300 DSP for Bert capability returns an error Configuration Error Option reconfiguration failed Configuration error Installed board not supported Configuration error OPTION, Invalid inconsistent license key Option UN7 hardware has an invalid revision of Fpga code Demodulator board has an invalid revision of DSP boot codeFpga download failed Demodulator board Modulation must have at least two states speciﬁed ﬁlter must have at least one coefﬁcient speciﬁedBurst shape ﬁle is corrupted, or is not in the proper format ﬁle is either corrupt or is not a FIR ﬁle