Agilent Technologies E4400-90333 manual 220, For errors -221 through, 215, Error, 214, 213

Page 48

-299 to -200: Execution Errors

ESG Family Signal Generators

-220	Parameter error
	A program data element related error has occurred. This particular error
	message is used if the device cannot detect a more speciﬁc error described
	for errors -221 through -229.
	Parameter error; <modulation file name>
	The speciﬁed ﬁle is not a modulation ﬁle type.
-215	Arm deadlock
	The arm source for the initiation of a measurement is set to GET and a
	subsequent measurement query is received. The measurement cannot
	begin until a GET is received, but the GET would cause an INTERRUPTED
	error.
-214	Trigger deadlock
	A trigger source for the initiation of a measurement is set to GET and a
	subsequent measurement query is received. The measurement cannot
	begin until a GET is received, but the GET would cause an INTERRUPTED
	error.
	Trigger deadlock
	TRIGger:SOURce BUS was selected when a MEASurement? query was
	executed. No data is returned.
-213	Init ignored
	A request for a measurement initiation was ignored as another
	measurement was already in progress.

Init ignored; Cannot initiate sweep in manual mode.

The manual mode is on and therefore the instrument cannot sweep.

Init ignored; Sweep is already initiated.

The list/sweep is currently initiated and sweeping, therefore the command is not legal according to SCPI.

Init ignored; Sweep is already continuously initiated.

The list/sweep is continuously initiated and sweeping, therefore the command is not legal according to SCPI.

46	Error Messages

Image 48

Contents Afﬁx Label Here Part No. E4400-90333 Supersedes February Copyright 1999-2001 Agilent TechnologiesContents Introduction Error Message Format Error Message Types No Error To -400 Query Errors To -300 Device-Speciﬁc Errors Device has detected a failure during its self-test procedureNearest Agilent Technologies sales or service ofﬁce Self-test for a particular power supply voltage has failed.Burst generator memory failed. Modulation data produced by 321Out of memory ARB communication failed Out of memory Could not copy current istate Out of memory Histogram display cannot function Out of memory Memory allocation error Out of memory Object Memory Area Lost. The meaning of this error is device-dependent Instrument is still functional320 315Non-volatile data saved by the *SAV? command has been lost Protected user data saved by the *PUD command has been lostAn error was detected in the device’s memory ValuesSystem error File Not Found To -200 Execution Errors When parsing a downloaded program is device-speciﬁc 285284 IllegalCommand header, or contained invalid header syntax Due to an error within the macro deﬁnition see Ieee 488.2Attempted. The deﬁnition of a math error is device-speciﬁc 276ﬁlename of was speciﬁed. This is not a legal ﬁlename An illegal memory subsystem name was used after the @File name error Illegal filename character File name not found SYSTEMFCDMA2KCHANFILE 254 Deﬁnition of what constitutes full media is device-speciﬁcCatalog. Afterwards, try again Try againSales or service ofﬁce 252What constitutes missing media is device-speciﬁc 250Measurement accuracy is questionable Data corrupt or stale filename During the ﬁrst power up after downloading new ﬁrmware into Algorithm. a potential cause is a failing backup batteryEeprom master copy if one exists. The system automatically 226223 Memory or related device-speciﬁc requirementsTo -200 Execution Errors Too much data User filter has too many symbols Data out of range Synthesizer Frequency out of bounds Data out of range value clipped to upper limit To -200 Execution Errors All digital modulation multicarriers must be the same format To -200 Execution Errors ESG Family Signal Generators Settings conflict Edge Bert requires Normal as Timeslot Type Settings conflict FM & PM not allowed Settings conflict GSM Bert requires Normal as Timeslot Type ESG Family Signal Generators Settings conflict I/Q & AM WB cannot be on at the same time ESG Family Signal Generators To -200 Execution Errors Used in RC1 Used in RC3 and 4 for channelTo -200 Execution Errors ESG Family Signal Generators For errors -221 through ErrorManual mode is on and therefore the instrument cannot sweep 220Have described the error that is stalling list/sweep 212Ignored 211Execution Error Cannot update FlexDG with Even Second Delay To -100 Command Errors Speciﬁed ﬁlename exceeds the maximum length Device cannot detect a more speciﬁc error Detect a more speciﬁc error150 148Header contains more than twelve characters see Ieee 488.2 110Command header error Syntax error 201 to 702 Device-Speciﬁc Errors Invalid ﬁle nameState ﬁle is not readable and the recall was aborted User has attempted to write to a read-only memory subsystemSynthesizer is unlocked. Service may be needed Internal error report to factoryInstrument’s output is unleveled 513 1 GHz Oscillator unlocked Calibration failure Dcfm DC overrange Reverse Power Protection RPP Tripped DSP FW download failed Demodulator board DSP times out Demodulator communication failed Option 300 DSP for Bert capability returns an error Configuration Error Option reconfiguration failed Configuration error Installed board not supported Configuration error OPTION, Invalid inconsistent license key Demodulator board has an invalid revision of DSP boot code Option UN7 hardware has an invalid revision of Fpga codeFpga download failed Demodulator board ﬁlter must have at least one coefﬁcient speciﬁed Modulation must have at least two states speciﬁedﬁle is either corrupt or is not a FIR ﬁle Burst shape ﬁle is corrupted, or is not in the proper format