Epson TX105, SX100, TX100, NX105, ME 300, SX105, TX101, TX106 Precautions, Tools, Name Epson Tool Code

Page 55

Epson STYLUS NX100/NX105/SX100/SX105/TX100/TX101/TX102/TX103/TX105/TX106/TX109/ME 300

Revision A

4.1 Overview

This section describes procedures for disassembling the main components of Epson STYLUS NX100/NX105/SX100/SX105/TX100/TX101/TX102/TX103/TX105/ TX106/TX109/ME 300. Unless otherwise specified, disassembled units or components can be reassembled by reversing the disassembly procedure. Procedures which, if not strictly observed, could result in personal injury are described under the heading “WARNING”. “CAUTION” signals a precaution which, if ignored, could result in damage to equipment. Important tips for procedures are described under the heading “CHECK POINT”. If the assembly procedure is different from the reversed disassembly procedure, the correct procedure is described under the heading “REASSEMBLY”. Any adjustments required after reassembly of components or parts are described under the heading “ADJUSTMENT REQUIRED”. When you have to remove any components or parts that are not described in this chapter, refer to the exploded diagrams in the appendix.

Read the following precautions before disassembling and assembling.

4.1.1 Precautions

See the precautions given under the heading “WARNING” and “CAUTION” in the following columns when disassembling or assembling Epson STYLUS NX100/ NX105/SX100/SX105/TX100/TX101/TX102/TX103/TX105/TX106/TX109/ME 300.

WARNING „ Disconnect the power cable before disassembling or assembling the printer.

„If you need to work on the printer with power applied, strictly follow the instructions in this manual.

„Always wear gloves for disassembly and reassembly to protect your eyes from ink. If any ink gets in your eyes, wash your eyes with clean water and consult a doctor immediately.

„Always wear gloves for disassembly and reassembly to avoid injury from sharp metal edges.

„To protect sensitive microprocessors and circuitry, use static discharge equipment, such as anti-static wrist straps, when accessing internal components.

„Never touch the ink or wasted ink with bare hands. If ink comes into contact with your skin, wash it off with soap and water immediately. If you have a skin irritation, consult a doctor immediately.

CAUTION

„ When transporting the printer after installing the ink cartridge,

 

pack the printer for transportation without removing the ink

 

cartridge and be sure to secure the Ink Cartridge to the printer

 

cover with tape tightly to keep it from moving.

„Use only recommended tools for disassembling, assembling or adjusting the printer.

„Observe the specified torque when tightening screws.

„Apply lubricants as specified. (See Chapter 6 “MAINTENANCE” (p108) for details.)

„Make the specified adjustments when you disassemble the printer. (See Chapter 5 “ADJUSTMENT” (p100) for details.)

„when reassembling the Waste Ink Tube, make sure that the tip of waste ink tube is placed in the correct position, otherwise ink may leak.

„When using compressed air products; such as air duster, for cleaning during repair and maintenance, the use of such products containing flammable gas is prohibited.

4.1.2Tools

Use only specified tools to avoid damaging the printer.

Table 4-1.

Tools

 

 

 

Name

 

EPSON Tool Code*

 

 

 

(+) Phillips screwdriver #1

 

1080530

 

 

 

(+) Phillips screwdriver #2

 

---

 

 

 

Flathead Precision screwdriver #1

 

---

 

 

 

Tweezers

 

---

 

 

 

Longnose pliers

 

---

 

 

 

Note * : All of the tools listed above are commercially available.

EPSON provides the tools listed with EPSON tool code.

DISASSEMBLY/ASSEMBLY

Overview

55

Confidential

Image 55
Contents Confidential Confidential Precautions About This Manual Revision Status Revision Date of Issue DescriptionContents Maintenance Product Description External View FeaturesBasic Specifications Printing SpecificationsInk Cartridge Media Print Mode Resolution Dot Size cps Print ModePrint Mode Color Print Mode MonochromeAsia Paper Name Paper Size Thickness WeightSupported Paper Supported Paper#DL Printing Area Margins Scanner SpecificationsPrinting Area Scanning RangeEnvironmental Conditions General SpecificationsElectrical Specifications 10. Primary Power SpecificationsUSB Interface Safety Approvals Safety standards/EMIInterface DurabilityButton/LED Function Control PanelOperation Buttons & LEDs 15. Buttons & LEDs16. Buttons Functions Control Panel FunctionsButton Printer Status Functions Revision a 17. LED Functions Priority Power LED Paper LED Ink LEDSetting for Stand-alone Copy Supported Paper and Copy ModeStand-alone Copy Function 21. Conditions for Storing the Scanned Data Copy SpeedMultiple Copying 20. Copy SpeedOperating Principles Printer Mechanism OverviewPrinter Mechanism Motors & Sensors Motors & SensorsScanner Mechanism CIS & Motor Nozzle Layout PrintheadTroubleshooting Disassembled and re-assembled correctly while referring to Identifying the causes of problems. The parts should bePreliminary Checks Specified ToolsError Indications and Fault Occurrence Causes Error Indications and Fault Occurrence CausesCheck point for Fatal error according to each phenomenon Troubleshooting by Error MessageMaintenance p.116. TBD Main Board When turning on the power, the PF Motor Carriage Unit collides with the Upper Encoder FFC Cap Assy Lever Cleaner Refer to Ink System p.77 Upper Paper Guide Check point for Paper jam error according to each phenomenon Top edge of paper is not loaded to Check point for Paper out error according to each phenomenon Guide pin Clutch LD Roller Shaft Extension Spring Paper Back Lever CR Contact Module PS Board Cable Panel FFC Superficial Phenomenon-Based Troubleshooting 11. Check point for the defective scanned image quality 10. Check point for the abnormal noise12. Check point for the defective printing quality TBD Printer driver Check point for Paper out error according to Ink stain of paper 13. Sensor check point Motor and Sensor TroubleshootingMotor Motor Type Drive Voltage Resistance DISASSEMBLY/ASSEMBLY Name Epson Tool Code PrecautionsTools ToolsWork Completion Check Work Completion CheckClassification Check Point Status Start Disassembly ProceduresPaper Support Tray Removing the HousingStacker Assy Removing the ASF Cover Document Cover/ASF CoverScanner Stand Scanner Stand /Cover Wire11. Installing the Cover Wire Scanner Unit When removing the FFC and the cable from the connectors asOn the Main Board, otherwise, it may gets damaged 14. Removing the Middle Housing Middle HousingBoard and the Panel Board on the rear of the Panel Unit are „ Be careful when removing the Panel Unit, because the MainRemoving the Circuit Boards Panel UnitMain Board CN No Cable Cable Color Connector Pins22. Installing the Main board Power Supply UnitDowel Rib Protrusion Positioning Hole 26. Removing the Printhead Disassembling the Printer Mechanism30. Removing the Printhead 27and -31 36. Removing the CR Scale CR Scale37. Removing the Hopper HopperDo not damage the PF Scale PF Encoder/ PF ScaleEJ Roller/ EJ Frame Assy Do not touch the PF Scale with bare handsMaintenance p.108 45. Removing the CR Motor CR Motor/ Driven Pulley47. Installing the CR Motor 50. Removing the Cap Assy Ink System52. Removing the Cap Assy Felt Wiper 56. Installing the Pump Assy58. Disassembling the Cap Assy Disassembling the Pump Assy 67. Removing the PF Motor PF MotorBe careful of not to break the soldered portions Do not damage the Pinion GearUpper Paper Guide with bare hands to avoid degrading Main FramePrint quality Main Frame „ Do not damage the PF Scale and the Lever Pick Clutch withWhenever the Upper Paper Guide is removed/replaced, Required adjustments must be carried outUpper Paper Guide With bare hands to avoid degrading the print quality78. Removing the CR Unit CR Unit83. Installing the CR Unit Whenever the CR Unit is removed/replaced, the required Adjustments must be carried outHands or damage it to avoid degrading the print quality PF RollerWhenever the PF Roller is removed/replaced, the required Quality LD Roller/ ASF Unit93. Removing the Lever Pick Clutch 99. Removing the Waste Ink Pads Waste Ink Pads102. Installing the Waste Ink Pads Confidential Disassembling the Scanner Unit Upper Scanner HousingScanner Unit, make sure to assemble the part referring to Carriage Unit Do not scratch the Rod Lens Array when removing the ScannerGrease on the rail of the Lower Scanner Housing Scanner Carriage Unit113. Replacing the Spacers 114. Removing the Scanner Motor Unit Scanner Motor UnitAdjustment Servicing Adjustment Item List TBD Adjustment Items and OverviewAdjustment Item Purpose Method Outline Tool Additional Functions Purpose Method Outline Tool Maintenance ItemsAdditional Functions Purpose Method Outline ToolRequired Adjustment List Required Adjustments TBDAdjustment Items and Overview 104 Measurement result Selection of adjustment value Using the Adjustment Program TBDTOP Margin Adjustment First Dot Position AdjustmentBi-D Adjustment Head Angular AdjustmentAdditional Information PF Band Adjustment Printout Pattern How to Judge PF AdjustmentMaintenance Service Maintenance CleaningLubrication Overview 111 Appendix Exploded Diagram / Parts List
Related manuals
Manual 3 pages 52.32 Kb

TX101, SX105, TX106, ME 300, TX102 specifications

Epson has long been a prominent player in the printing industry, and its series of all-in-one inkjet printers, including the TX109, TX100, SX100, NX105, and TX103, showcase the brand’s commitment to innovation and performance.

The Epson TX109 is a versatile all-in-one inkjet printer that offers printing, scanning, and copying functions, making it ideal for both home and office use. One of its standout features is the ability to produce high-quality prints at an impressive resolution of up to 5760 x 1440 dpi. Additionally, the TX109 utilizes Epson's Micro Piezo technology, which ensures precise droplet control for sharp images and text. It supports various media types, enabling users to print everything from documents to photos, while its compact design facilitates easy placement in smaller spaces.

Similarly, the TX100 is designed for ease of use and efficiency. It features a simple user interface, making it accessible to users of all skill levels. With a print speed of up to 27 pages per minute for black and white documents, the TX100 enhances productivity. Furthermore, it supports the economical use of ink with individual cartridges, allowing users to replace only the colors they need.

The SX100 takes functionality a step further, offering an integrated flatbed scanner. This model is ideal for users who require additional scanning capabilities without investing in separate devices. It also maintains the high-quality printing standards that Epson is known for, providing vibrant colors and sharp details.

The NX105 combines the best features of its predecessors, sporting enhanced wireless connectivity capabilities. This allows users to print directly from various smart devices, making it perfect for modern home environments where mobility is essential. Like others in the series, the NX105 excels in producing borderless photos and can print up to a maximum resolution of 5760 x 1440 dpi.

Lastly, the TX103 also stands out with its multifunctionality and space-saving design. Beyond printing, scanning, and copying, it features an easy-to-navigate interface. Users benefit from high-speed printing capabilities and can produce quality documents quickly.

In summary, the Epson TX series—including the TX109, TX100, SX100, NX105, and TX103—offers a blend of quality, efficiency, and advanced technology. Each model incorporates innovations that cater to the needs of everyday users, making them suitable for a variety of tasks while maintaining affordability and ease of maintenance.