Kodak 9090DC, 9125DC, 9150DC, 9090DB manual Settings button, Resetting the maintenance reminders

Page 35

Resetting the maintenance reminders

If a maintenance interval expires triggering the maintenance reminder, a hyperlink for that component will navigate you to reset and restart the interval count. This process is necessary to ensure required maintenance continues to be monitored appropriately.

NOTE: The alert intervals for calibrating the front and back cameras cannot be adjusted. If an alert to calibrate the camera(s) is displayed, click the corresponding hyperlink to perform the calibration procedure. For procedures on calibrating the cameras, see Chapter 6, Maintenance.

Settings button	When you click the Settings button on the Ngenuity Operator Utility
	main screen, the Configure Scanner Settings screen will be displayed.

You can configure basic scanner settings using this screen.

Sleep timeout — you can set the delay time in hours and minutes that the scanner can be idle with full power before going into sleep mode. The default timeout is 15 minutes; the maximum time is 4 hours.

NOTE: Sleep mode can also be entered manually by pressing the Pause/Stop button on the control panel. See the section entitled, “Batch Control” earlier in this chapter for more information.

Multifeed — allows you to adjust the sensitivity when scanning Normal or Very thin documents.

•Normal: for documents that range from thick card stock to thin carbon copies. This setting should be used for most documents.

•Very thin: used to detect multifeeds when scanning ultra-thin documents such as rice paper.

A-61662 October 2011

4-15

Image 35

Contents Page User Precautions SafetyUnited States Japan Environmental informationEuropean Union Acoustic emission EMC statementsEuropean Union Peoples Republic of China KoreaPage Overview ContentsWhat’s in the box Front view Scanner componentsStandard Exit Deflector Lightweight Exit Deflector Page Page Rear view Contents Installing the exit deflector InstallationInstallation with a USB connection Installation with an optional Scsi connection Page Getting Started Maximum thickness Getting your documents ready to scanManually feeding documents Select the Accelerated Scanning tab Accelerated scanning VRS onlyControl Panel and Ngenuity Operator Utility Control panel Status Door, Maintenance and Manual FeedSteady on Maintenance LED Scanner state Off not litSlow blinking Fast blinkingCustom functions Clean Print HeadFeeder table Down/SetFor more information, see , Advanced Features Batch Control Ngenuity Batch Counter Ngenuity Operator Utility Ngenuity Operator Utility main screen Scanner menu Menu barFeature Access Help menu ScannerDetails, Feature AccessUnlock and the HelpHome screen Page Resetting the maintenance reminders Settings buttonVolume can be set to Mute, Low, Medium or High Advanced settings Page Reminder Range Default Maintenance buttonAdvanced Properties dialog box Advanced FeaturesAccessing Advanced features Advanced Properties dialog box Color screen Page Rotation screen Preferences Black & White SettingsPage Document Conflicting Controls ResolutionCamera Modes Multifeed screen Page About screen Maintenance Sensors Cleaning suppliesMaintenance Recommended Range Symptoms Glass Camera Covers / Imaging GuidesPage Cleaning the pick and drive rollers Cleaning the separation roller Page Cleaning the imaging guides and camera glass covers Imaging guide removed Camera cover Lamp Cleaning the sensors Exit sensor Test Batch Cleaning the transportReplacing tires Replacement proceduresGuides Replacing the preSeparation pad Replacing the imagingCamera calibration Page Supplies and consumables Accessories CAT NoClearing a document jam TroubleshootingSymptom Cause Remedy Installation/Setup/Connectivity Problem solvingImage and Feeding Error Message Possible Cause Possible RemedyContacting Service Appendix a Specifications Operating system RecommendedMinimum Installing the front page imprinter and ink cartridge Appendix B Installing and Using the ImprinterSpecifications Installing the front page imprinter and ink cartridgeCenter position Removing the front imprinter Installing the back page imprinter and ink cartridge Removing the back imprinter Subject Specification MaintenanceInk cartridge specifications Print head Cleaning the ink cartridgeAdditional print head CleaningSpit pad replacement Print positions Carriage tab Click Text Controls Counter Date & Time Example Format Code Special Content Code Example Page Increment on Patch Code Reset on Patch CodeIncrement on Patch Code and Reset on Patch Code options are Patch Code optionsContents Page Appendix D Glossary Appendix E Patch Code Information KEY Numeric code Graphical Pattern Comment Key for Graphical Pattern DescriptionPatch Patch codesPatch