Emerson 4015 installation instructions Power and Control Sub-Rack, Battery Tray

Page 33

Installation Instructions	IM584000300
Spec. No. 584000300 (Model 4015-X003)	Issue AB, April 3, 2013

	Battery Tray Alarm / Control Connections - 1 Tray Only

Power and Control

Sub-Rack

Rear

1.Remove a termination plug from one of the connectors (either one) located on the rear of the power and control sub-rack.

2.Plug the extension control/alarm cable

into the connector the termination plug was removed from.

3.Connect the other end of the extension control/alarm cable into the battery tray control/alarm harness.

Internal/External Battery Tray Control/Alarm Connectors

(If an internal or external battery tray is not connected, MUST have termination plugs installed.) (Use either connector.)

Extension Control/Alarm Cable (P/N 554715) (56”)

Battery Tray

Control/Alarm

Harness

Battery

Tray

Rear

Figure 3-7 (cont’d on next page)

Internal Battery Tray Interconnections

Chapter 3. Making Electrical Connections

Page 23

This document is property of Emerson Network Power, Energy Systems, North America, Inc. and contains confidential and proprietary information owned by Emerson Network Power, Energy

Systems, North America, Inc. Any copying, use, or disclosure of it without the written permission of Emerson Network Power, Energy Systems, North America, Inc. is strictly prohibited.

Image 33

Contents IM584000300 Issue AB, April 3 Installation InstructionsPage Table of Contents Issue AB, April 3 Spec. No Model Important Safety Instructions General SafetyVoltages AC Input Voltages DC Input/Output VoltagesBattery if Equipped Personal Protective Equipment PPE Dual Hazardous Input Power Sources Maintenance and Servicing ProceduresCircuit Card Handling GeneralStatic Warning IM584000300 Customer Documentation Package Bound System Installation ManualSystem Packaging USB Drive with All Customer DocumentationTemperature Probes List 98 Part Number Qty Power and Control Sub-Rack List 11General Part Number Qty Rectifiers Part Number QtyDC Load Distribution Sub-Rack List 21, 22, 23 Battery Tray List 91 Recommended Tools and Test Equipment Installation Acceptance Checklist Checklist -Factory Integrated System List R1, R2General Checklist Customer Integrated System ship loose Air Flow Diagram Installing the System General RequirementsAir Flow Storing for Delayed Installation Inspecting the Equipment Storing for Delayed InstallationsSecuring the IT Rack to the Floor Inspecting the EquipmentInstalling the Sub-Racks Installing Individual SUB-RACKS Into CutomerFor customer provided IT rack installation only Customer Supplied IT Rack GuidelinesIM584000300 Mounting Details Electrically Interconnecting the Sub-RacksOutput Ground Configurations Important Safety Instructions Wiring ConsiderationsTorque Cable RoutingSub-Rack IM584000300 Removable Panel Tasks to be Performed for Customer Integrated Systems Hrmg Configurations Only Bus Grounding ConnectionGrounding Sub-Rack Grounding Frame GroundBattery Tray Issue AB, April 3 Spec. No Model Load Distribution Sub-RackLoad Distribution Sub-Rack Power and Control Sub-Rack Sub-Racks Electrical Interconnections Sub-Rack Interconnections Making Electrical Connections Power and Control Sub-Rack Battery Tray Tasks to be Perform for ALL Installations IT Rack Grounding Frame GroundConduit Grounding Frame Ground Grounding Scheme Diagram Hrmg System GroundingNPG System Grounding Suggested AC Input Power Connections Making Electrical Connections AC Input Power ConnectionsNPG Negative Pole Ground Configuration Hrmg High Resistance Midpoint Ground ConfigurationLoad Distribution Sub-Rack Battery Manufacturer Information Installing Battery Sub-TraysRefer to -12as this procedure is performed Battery Sub-Trays External Battery Connections if required Customer Connection To External Battery Strings External Battery Connections Making Electrical ConnectionsDigital Inputs and Programmable Relay Outputs IB2 ACU+ Controller Interface Board Connections if requiredDigital Inputs Programmable Relay OutputsInstallation Instructions Issue AB, April 3 Spec. No Model Temperature ProbesACU+ Controller Ethernet Connection if required Power and Control Sub-Rack Programmable J6-3 None J6-1 J6-6 J6-5J6-4 None J6-2 J7-5 J7-3 None J7-1 J7-6Power and Control Chapter Installing the Rectifier Module Circuit Breaker Locations Initially Starting the System Initial Startup PreparationInitially Starting the System ACU+ Controller Local Indicators and Navigation Keys ACU+ Controller InitializationVersion ***** Starting… IM584000300 Changing Battery Capacity Rating in the ACU+ Verifying the Configuration FileProcedure To Select a Sub-Menu Checking Basic System SettingsTo Enter a Password To Change a ParameterPage Configuring the ACU+ Identification of Rectifiers Checking System Status Checking the System Shutdown CircuitReference Documents Final StepsECO Change Issue Number Description of ChangeFor More Information NetPerform Optimization Services