Schneider Electric 66846, 66074 user manual Network Management Card

Page 2

Network

Management Card

User Manual

Table of Contents

1MGE NETWORK SOLUTION ____________________________________________________________5

1.1INTRODUCTION _____________________________________________________________________5

1.1.1Connecting the UPS / STS to the Network ___________________________________________5 The Network Management Card: __________________________________________________________5

1.1.2Protecting the computers / servers _________________________________________________6

1.1.3Monitoring the UPSs over the network ______________________________________________6

1.1.4Connection____________________________________________________________________7

1.2PRESENTATION OF THE NETWORK MANAGEMENT CARDS (NMC) ________________________________7

1.3PRESENTATION OF THE ENVIRONMENT SENSOR SOLUTION _____________________________________8

1.4DIRECT SENDING OF E-MAIL____________________________________________________________8

1.5SENDING TEXT MESSAGES (SMS) _______________________________________________________8

1.6COMPATIBILITY WITH THE NETWORK MANAGEMENT SYSTEMS (NMS) – TRAP SENDING ________________8

1.7TECHNICAL DATA ___________________________________________________________________9

1.7.1Configuration __________________________________________________________________9

1.7.2Administration _________________________________________________________________9

1.7.3Network ______________________________________________________________________9

1.7.4MIB (Management Information Base) _______________________________________________9

1.7.5Environment sensor _____________________________________________________________9

2INSTALLATION AND CONFIGURATION__________________________________________________11

2.1INSTALLATION _____________________________________________________________________11

2.1.1Installing the card in the UPS / STS _______________________________________________11

2.1.2Connecting the card to the IT network______________________________________________11

2.1.3Understanding front panel signals _________________________________________________11

2.2BASIC CONFIGURATION ______________________________________________________________11

2.2.1List of default parameters _______________________________________________________11

2.2.2Adjusting the network parameters _________________________________________________11

2.2.3Rebooting the card ____________________________________________________________11

2.2.4Restoring factory configuration ___________________________________________________11

2.2.5Lost password – restoring the default password ______________________________________11

2.2.6Checking that the card is working _________________________________________________11

2.3ENVIRONMENT SENSOR ______________________________________________________________11

3SUPERVISION / ADMINISTRATION VIA A WEB BROWSER _________________________________12

3.1OPTIMISING THE PERFORMANCE OF YOUR BROWSER_________________________________________12

3.2UPS / STS _______________________________________________________________________13

3.2.1“UPS properties” page __________________________________________________________13

3.2.2“STS properties” page __________________________________________________________15

3.2.3About _______________________________________________________________________16

3.2.4On-line help __________________________________________________________________17

3.2.5UPS 3-Phase display___________________________________________________________19

3.2.6STS 3-Phase display ___________________________________________________________21

3.2.7UPS Control __________________________________________________________________22

3.2.8UPS weekly schedule programming _______________________________________________24

3.2.9Shutdown parameters __________________________________________________________25

3.2.10Viewing the alarms ____________________________________________________________26

3.3LOGS ___________________________________________________________________________27

3.3.1UPS Measurements____________________________________________________________27

3.3.2STS Measurements ____________________________________________________________28

Network Management Card – User Manual

34003676EN/HA

Page 2/81

Page 1 Page 3
Image 2
Page 1 Page 3
Contents Network Management Card NMC Transverse Environment Sensor Network Management Card MAINTENANCE72 Software Upgrade ConfigurationConfiguration VIA Telnet Configuration VIA SSH Appendices Tables of Alarms and EventsGlossary Network Management Card Connecting the UPS / STS to the NetworkIntroduction Monitoring the UPSs over the network MGE supervisor Enterprise Power ManagerProtecting the computers / servers Network Shutdown module only available for UPS, not for STSConnection How to connect UPS / networkSetting up the protection, for UPS only Presentation of the Network Management Cards NMCSending text messages SMS Presentation of the Environment Sensor solutionDirect sending of E-mail Technical data 10/81 Environment Sensor InstallationBasic configuration Supervision / Administration via a Web browser Optimising the performance of your browserUPS zone general information on the UPS UPS / STSUPS properties UPS status zone essential informationBattery status zone STS status zone essential information STS propertiesSTS zone general information on the STS About Sources status zoneOn-line help 18/81 UPS 3-Phase display Normal input measurementsBattery measurements By Pass measurementsSTS 3-Phase display UPS Control Source 2 input measurement23/81 UPS weekly schedule programming Shutdown parameters Important noteViewing the alarms Logs UPS MeasurementsSTS Measurements 29/81 UPS Event log STS Event log31/81 System log 33/81 Notified events NotificationUPS Email Notification Mail message configuration see next Recipient ListOther settings STS Email NotificationSender Email Message SettingsUPS Email Message Settings SubjectSTS Email Message Settings Email Example Configuration User Name and password by default are MgeupsNetwork Settings 42/81 System 44/81 UPS Notified Applications 46/81 Central Shutdown Configuration STS Notified Applications 49/81 Access control 51/81 Access is disabled and the card is accessible in SSH Time Environment CharacteristicsStatus Configuration Log Environment status 56/81 UPS Environment Settings UPS Environment SettingsSTS Environment Settings Humidity4 Log Set-up of the shutdown parameters Shutdown criteria managed by the Management CardShutdown duration Specific set-up for long autonomy installation 30 mnShutdown when backup time is less than Different server and UPS shutdown sequences 63/81 4 Off/On command Configuring a set of cards with Mupgrade Configuration in local modeChoice 1 Snmp agent configuration menu MgeupsChoice 3 Access control Choice 2 UPS / STS parametersChoice 4 Restore default configuration Choice 5 Reset the cardPuTTY SSH Client Program Configuration via TelnetConfiguration via SSH 70/81 71/81 Card software upgrade via Tftp Unix and Windows Software upgradeCard firmware upgrade using Mupgrade Windows STS Alarm table Tables of alarms and eventsUPS Alarm table English FrenchUPS event table UPS STS event table 77/81 System alarm table Glossary Subnet mask TelnetTrap Snmp
Related manuals
Manual 18 pages 57.58 Kb
Top Page Image Contents