Schneider Electric 66846, 66074 user manual 42/81

Page 42

Network

Management Card

User Manual

◗Domain name is the domain to which the card belongs. This is the part of the full qualified domain name that follows the host name and is used by the DNS. The default value of the two parameters comprising the full qualified domain name: ups.domain.com

◗TELNET connection: Authorises (choose enable) remote connection with a terminal to access the maintenance menu.

See “Configuration in local mode and via Telnet “ for more information

◗BootP/DHCP: Authorises (choose enable) configuration of network parameters with your BootP/DHCP

server when the card is booted

Mode of card operation with server: after any reboot, if this option is enabled, the card tries to recover the network parameters from the server for 10 sec. If no response is received from the server, the card boots with the last saved parameters from the previous start. These parameters are those shown on the page The default value for this parameter is “Enable”

. Note:

The IP address supplied by the DHCP server must be fixed to maintain connection with the clients installed on the stations to be protected.

◗Network Upgrade: Authorises (choose enable) remote upgrading of the embedded system on the card using the Mupgrade tool. Read the “Maintenance” section for more details.

◗Primary DNS server: contains the IP address of the main DNS server ensuring conversion of the domain

name to IP address.

◗Secondary DNS server: contains the IP address of the secondary DNS server ensuring conversion of the domain name to IP address if the primary DNS server is not available.

◗SMTP server: contains the name or IP address of the local server with which the card connects to send e- mails.

It may be filled in either as host + domain name (DNS resolution), or directly with the IP address The default value is stmpserver.domain.com . The card uses port 25 to send e-mails.

◗The Authentication option must be selected if the SMPT server requires this parameter for query submission (see the RFC 2554 for SMTP authentication) for commercial reasons, access control, etc. When authentication is selected, the User and Password parameters must be specified for identification with the local SMTP server.

Default values are MGEUPS/MGEUPS.

Note: The card must be rebooted after any changes to these parameters. See “System”

Security: the administrator must click on Save and enter his login/password to save any modifications.

Network Management Card – User Manual

34003676EN/HA

Page 42/81

Page 41 Page 43
Image 42
Page 41 Page 43
Contents Network Management Card NMC Transverse Environment Sensor Network Management Card MAINTENANCE72 Software Upgrade ConfigurationConfiguration VIA Telnet Configuration VIA SSH Appendices Tables of Alarms and EventsGlossary Connecting the UPS / STS to the Network IntroductionNetwork Management Card Monitoring the UPSs over the network MGE supervisor Enterprise Power ManagerProtecting the computers / servers Network Shutdown module only available for UPS, not for STSConnection How to connect UPS / networkSetting up the protection, for UPS only Presentation of the Network Management Cards NMCPresentation of the Environment Sensor solution Direct sending of E-mailSending text messages SMS Technical data 10/81 Installation Basic configurationEnvironment Sensor Supervision / Administration via a Web browser Optimising the performance of your browserUPS zone general information on the UPS UPS / STSUPS properties UPS status zone essential informationBattery status zone STS properties STS zone general information on the STSSTS status zone essential information About Sources status zoneOn-line help 18/81 UPS 3-Phase display Normal input measurementsBattery measurements By Pass measurementsSTS 3-Phase display UPS Control Source 2 input measurement23/81 UPS weekly schedule programming Shutdown parameters Important noteViewing the alarms Logs UPS MeasurementsSTS Measurements 29/81 UPS Event log STS Event log31/81 System log 33/81 Notification UPS Email NotificationNotified events Mail message configuration see next Recipient ListOther settings STS Email NotificationSender Email Message SettingsUPS Email Message Settings SubjectSTS Email Message Settings Email Example Configuration User Name and password by default are MgeupsNetwork Settings 42/81 System 44/81 UPS Notified Applications 46/81 Central Shutdown Configuration STS Notified Applications 49/81 Access control 51/81 Access is disabled and the card is accessible in SSH Time Characteristics Status Configuration LogEnvironment Environment status 56/81 UPS Environment Settings UPS Environment SettingsSTS Environment Settings Humidity4 Log Set-up of the shutdown parameters Shutdown criteria managed by the Management CardSpecific set-up for long autonomy installation 30 mn Shutdown when backup time is less thanShutdown duration Different server and UPS shutdown sequences 63/81 4 Off/On command Configuring a set of cards with Mupgrade Configuration in local modeChoice 1 Snmp agent configuration menu MgeupsChoice 3 Access control Choice 2 UPS / STS parametersChoice 4 Restore default configuration Choice 5 Reset the cardConfiguration via Telnet Configuration via SSHPuTTY SSH Client Program 70/81 71/81 Software upgrade Card firmware upgrade using Mupgrade WindowsCard software upgrade via Tftp Unix and Windows STS Alarm table Tables of alarms and eventsUPS Alarm table English FrenchUPS event table UPS STS event table 77/81 System alarm table Glossary Subnet mask TelnetTrap Snmp
Related manuals
Manual 18 pages 57.58 Kb
Top Page Image Contents