Schneider Electric 66074, 66846 user manual Logs, UPS Measurements

Page 27

Network

Management Card

User Manual

3.3Logs

3.3.1 UPS Measurements

Click on the “Measurements” section in the menu.

The following measurements are saved and time-stamped:

◗“Input voltage” : Value of the utility voltage supplying your UPS (average of 3 phases for UPS' equipped with a 3-phase input)

◗“Input frequency” : Value of the utility frequency feeding your UPS

◗“Output voltage”: Value of the output voltage of your UPS (average of the 3 phases for UPS’ with a 3- phase output)

◗“Output load” : Value of the percentage of load at UPS output (Value of the most loaded phase for 3-phase UPS’)

◗“ Output current Ph x”: Value of the output current for each phase on three-phase UPSs

◗“Battery capacity”: Percentage of charge available in the battery

◗“Remaining time” : Estimation of the remaining backup time

◗The save frequency of these values is defined in the “System” page (60 seconds by default). Approximately 1000 time-stamps are stored permanently on the card. The oldest time-stamps are automatically deleted.

◗“Save” enables all saved values to be opened or saved in CSV format (compatible with Excel type

spreadsheets)

“Clear” enables deletion of all records. The administrator must enter his login / password to validate this action if he has not already done so during the current session.

Select the time range to view

Network Management Card – User Manual

34003676EN/HA

Page 27/81

Page 26 Page 28
Image 27
Page 26 Page 28
Contents Network Management Card NMC Transverse Environment Sensor Network Management Card Appendices Tables of Alarms and Events ConfigurationConfiguration VIA Telnet Configuration VIA SSH MAINTENANCE72 Software UpgradeGlossary Connecting the UPS / STS to the Network IntroductionNetwork Management Card Network Shutdown module only available for UPS, not for STS MGE supervisor Enterprise Power ManagerProtecting the computers / servers Monitoring the UPSs over the networkPresentation of the Network Management Cards NMC How to connect UPS / networkSetting up the protection, for UPS only ConnectionPresentation of the Environment Sensor solution Direct sending of E-mailSending text messages SMS Technical data 10/81 Installation Basic configurationEnvironment Sensor Optimising the performance of your browser Supervision / Administration via a Web browserUPS status zone essential information UPS / STSUPS properties UPS zone general information on the UPSBattery status zone STS properties STS zone general information on the STSSTS status zone essential information Sources status zone AboutOn-line help 18/81 Normal input measurements UPS 3-Phase displayBy Pass measurements Battery measurementsSTS 3-Phase display Source 2 input measurement UPS Control23/81 UPS weekly schedule programming Important note Shutdown parametersViewing the alarms UPS Measurements LogsSTS Measurements 29/81 STS Event log UPS Event log31/81 System log 33/81 Notification UPS Email NotificationNotified events Recipient List Mail message configuration see nextSTS Email Notification Other settingsSubject Email Message SettingsUPS Email Message Settings SenderSTS Email Message Settings Email Example User Name and password by default are Mgeups ConfigurationNetwork Settings 42/81 System 44/81 UPS Notified Applications 46/81 Central Shutdown Configuration STS Notified Applications 49/81 Access control 51/81 Access is disabled and the card is accessible in SSH Time Characteristics Status Configuration LogEnvironment Environment status 56/81 UPS Environment Settings UPS Environment SettingsHumidity STS Environment Settings4 Log Shutdown criteria managed by the Management Card Set-up of the shutdown parametersSpecific set-up for long autonomy installation 30 mn Shutdown when backup time is less thanShutdown duration Different server and UPS shutdown sequences 63/81 4 Off/On command Configuration in local mode Configuring a set of cards with MupgradeMgeups Choice 1 Snmp agent configuration menuChoice 2 UPS / STS parameters Choice 3 Access controlChoice 5 Reset the card Choice 4 Restore default configurationConfiguration via Telnet Configuration via SSHPuTTY SSH Client Program 70/81 71/81 Software upgrade Card firmware upgrade using Mupgrade WindowsCard software upgrade via Tftp Unix and Windows English French Tables of alarms and eventsUPS Alarm table STS Alarm tableUPS event table UPS STS event table 77/81 System alarm table Glossary Telnet Subnet maskTrap Snmp
Related manuals
Manual 18 pages 57.58 Kb
Top Page Image Contents