Schneider Electric 66074, 66846 user manual Ups

Page 75

Network

Management Card

User Manual

UPS return to normal temperature

Fin de défaut température

%s on sequence started

Début séquence de démarrage%s

%s on sequence cancelled

Arrêt séquence de démarrage %s

%s on sequence in progress

Séquence de démarrage %sen cours

%s on sequence completed

Fin séquence de démarrage%s

%s off sequence started

Début séquence d’arrêt %s

%s off sequence cancelled

Arrêt séquence d’arrêt %s

%s off sequence in progress

Séquence d’arrêt %s en cours

%s off sequence completed

Fin séquence d’arrêt %s

%s toggle (off/on) sequence started

Début séquenced’arrêt/marche %s

%s toggle (off/on) sequence cancelled

Arrêt séquenc e d’arrêt/marche %s

%s toggle (off/on) sequence in

Séquence d’arrêt/marche %s en cours

progress

 

%s toggle (off/on) sequence completed

Fin séquence d’arrêt/marche %s

UPS

onduleur

UPS communication failed

Perte de communication avec l’onduleur

UPS communication restored

Retour de communication avec l’onduleur

Unavailable battery

Batterie indisponible

Battery available

Batterie disponible

UPS waiting for battery charging

UPS waiting for battery charging condition

condition

 

UPS reached battery charging

UPS reached battery charging condition

condition

 

UPS fault

défaut interne

UPS OK

Fin défaut interne

UPS passed battery test

Test batterie terminé

UPS failed battery test

Test batterie en défaut

UPS enter environment external alarm

UPS enter environment external alarm

UPS exit environment external alarm

UPS exit environment external alarm

Buck activated on UPS

Onduleur en mode Buck

Buck de-activated on UPS

Mode Buck désactivé

Normal input switch (Q1) closed

Interrupteur d'entrée (Q1) fermé

Normal input switch (Q1) open

Interrupteur d'entrée (Q1) ouvert

Bypass switch (Q4S) closed

Interrupteur bypass (Q4S) fermé

Battery switch (QF1) closed

Disjoncteur batterie QF1 fermé

Battery switch (QF1) open

Disjoncteur batterie QF1 ouvert

Manual bypass switch (Q3BP) closed

Interrupteur bypass manual (Q3BP) fermé

Manual bypass switch (Q3BP) open

Interrupteur bypass manual (Q3BP) ouvert

Output switch (Q5N) closed

Interrupteur de sortie (Q5N) fermé

Output switch (Q5N) open

Interrupteur de sortie (Q5N) ouvert

Output not protected

Sortie non protégée

Output On

Sortie alimentée

<Sensor name>: Temperature is below

<Sensor name>: La température est en

low threshold %d °C

dessous du seuil bas %d °C

<Sensor name>: Temperature is

<Sensor name>: La température est au

above high threshold %d °C

dessus du seuil haut %d °C

<Sensor name>: Temperature is in

<Sensor name>: La température est revenue à

normal range

un niveau normal

<Sensor name>: Humidity is below low

<Sensor name>: L'humidité est en dessous du

threshold %d %

seuil bas %d %

<Sensor name>: Humidity is above

<Sensor name>: L'humidité est au dessus du

high threshold %d %

seuil haut %d %

Network Management Card – User Manual

34003676EN/HA

Page 75/81

Image 75
Contents Network Management Card NMC Transverse Environment Sensor Network Management Card Appendices Tables of Alarms and Events ConfigurationConfiguration VIA Telnet Configuration VIA SSH MAINTENANCE72 Software UpgradeGlossary Connecting the UPS / STS to the Network IntroductionNetwork Management Card Network Shutdown module only available for UPS, not for STS MGE supervisor Enterprise Power ManagerProtecting the computers / servers Monitoring the UPSs over the networkPresentation of the Network Management Cards NMC How to connect UPS / networkSetting up the protection, for UPS only ConnectionPresentation of the Environment Sensor solution Direct sending of E-mailSending text messages SMS Technical data 10/81 Installation Basic configurationEnvironment Sensor Optimising the performance of your browser Supervision / Administration via a Web browserUPS status zone essential information UPS / STSUPS properties UPS zone general information on the UPSBattery status zone STS properties STS zone general information on the STSSTS status zone essential information Sources status zone AboutOn-line help 18/81 Normal input measurements UPS 3-Phase displayBy Pass measurements Battery measurementsSTS 3-Phase display Source 2 input measurement UPS Control23/81 UPS weekly schedule programming Important note Shutdown parametersViewing the alarms UPS Measurements LogsSTS Measurements 29/81 STS Event log UPS Event log31/81 System log 33/81 Notification UPS Email NotificationNotified events Recipient List Mail message configuration see nextSTS Email Notification Other settingsSubject Email Message SettingsUPS Email Message Settings SenderSTS Email Message Settings Email Example User Name and password by default are Mgeups ConfigurationNetwork Settings 42/81 System 44/81 UPS Notified Applications 46/81 Central Shutdown Configuration STS Notified Applications 49/81 Access control 51/81 Access is disabled and the card is accessible in SSH Time Characteristics Status Configuration LogEnvironment Environment status 56/81 UPS Environment Settings UPS Environment SettingsHumidity STS Environment Settings4 Log Shutdown criteria managed by the Management Card Set-up of the shutdown parametersSpecific set-up for long autonomy installation 30 mn Shutdown when backup time is less thanShutdown duration Different server and UPS shutdown sequences 63/81 4 Off/On command Configuration in local mode Configuring a set of cards with MupgradeMgeups Choice 1 Snmp agent configuration menuChoice 2 UPS / STS parameters Choice 3 Access controlChoice 5 Reset the card Choice 4 Restore default configurationConfiguration via Telnet Configuration via SSHPuTTY SSH Client Program 70/81 71/81 Software upgrade Card firmware upgrade using Mupgrade WindowsCard software upgrade via Tftp Unix and Windows English French Tables of alarms and eventsUPS Alarm table STS Alarm tableUPS event table UPS STS event table 77/81 System alarm table Glossary Telnet Subnet maskTrap Snmp
Related manuals
Manual 18 pages 57.58 Kb