Schneider Electric 66074 Configuring a set of cards with Mupgrade, Configuration in local mode

Page 65

Network

Management Card

User Manual

5 Configuring a set of cards with Mupgrade

This feature is particularly useful to configure large UPSs / STSs installed base.

The Remote configuration features of Mupgrade allows you to import, modify and export configuration files from and to Network Management Cards.

Configure all your Network Management Cards in four step :

1.Configure a Network Management Card located on the network through the html interface to create a master configuration..

2.Import this configuration from the master card in Mupgrade.

3.Edit and change some parameters , select the fields which must be overwritten in the destination cards and save the new configuration in a file.

4.Export the new configuration to other cards which have same firmware release as the master card Read the relevant documentation available for download on the www.apc.com web site.

6 Configuration in local mode and via Telnet or SSH

6.1Configuration in local mode

◗Use the cable supplied with the card.

◗Connect the card to a computer equipped with a hyper-terminal type emulator. The serial link should be set at 9600 bauds, 8 bits, no parity, 1 stop bit and no flow control.

◗Check that UPS power is on.

◗A few seconds after terminal opening, press the "Enter” button. The menu asks you to enter your password (MGEUPS by default), and then press “ Enter”.

◗The card will disconnect itself after 3 minutes of inactivity.

◗The menu is in English only.

+===========================================================================

+

[ MGE UPS SYSTEMS SNMP/Web agent Configuration menu ] +===========================================================================

+

Enter Password: ******

+===========================================================================

+

[ MGE UPS SYSTEMS SNMP/Web agent Configuration menu ] +===========================================================================

+

1.Agent Configuration

2.UPS/STS Parameters

3.Access Control Table

Network Management Card – User Manual

34003676EN/HA

Page 65/81

Image 65

Contents Network Management Card NMC Transverse Environment Sensor Network Management Card Configuration VIA Telnet Configuration VIA SSH ConfigurationMAINTENANCE72 Software Upgrade Appendices Tables of Alarms and EventsGlossary Network Management Card Connecting the UPS / STS to the NetworkIntroduction Protecting the computers / servers MGE supervisor Enterprise Power ManagerMonitoring the UPSs over the network Network Shutdown module only available for UPS, not for STSSetting up the protection, for UPS only How to connect UPS / networkConnection Presentation of the Network Management Cards NMCSending text messages SMS Presentation of the Environment Sensor solutionDirect sending of E-mail Technical data 10/81 Environment Sensor InstallationBasic configuration Optimising the performance of your browser Supervision / Administration via a Web browserUPS properties UPS / STSUPS zone general information on the UPS UPS status zone essential informationBattery status zone STS status zone essential information STS propertiesSTS zone general information on the STS Sources status zone AboutOn-line help 18/81 Normal input measurements UPS 3-Phase displayBy Pass measurements Battery measurementsSTS 3-Phase display Source 2 input measurement UPS Control23/81 UPS weekly schedule programming Important note Shutdown parametersViewing the alarms UPS Measurements LogsSTS Measurements 29/81 STS Event log UPS Event log31/81 System log 33/81 Notified events NotificationUPS Email Notification Recipient List Mail message configuration see nextSTS Email Notification Other settingsUPS Email Message Settings Email Message SettingsSender SubjectSTS Email Message Settings Email Example User Name and password by default are Mgeups ConfigurationNetwork Settings 42/81 System 44/81 UPS Notified Applications 46/81 Central Shutdown Configuration STS Notified Applications 49/81 Access control 51/81 Access is disabled and the card is accessible in SSH Time Environment CharacteristicsStatus Configuration Log Environment status 56/81 UPS Environment Settings UPS Environment SettingsHumidity STS Environment Settings4 Log Shutdown criteria managed by the Management Card Set-up of the shutdown parametersShutdown duration Specific set-up for long autonomy installation 30 mnShutdown when backup time is less than Different server and UPS shutdown sequences 63/81 4 Off/On command Configuration in local mode Configuring a set of cards with MupgradeMgeups Choice 1 Snmp agent configuration menuChoice 2 UPS / STS parameters Choice 3 Access controlChoice 5 Reset the card Choice 4 Restore default configurationPuTTY SSH Client Program Configuration via TelnetConfiguration via SSH 70/81 71/81 Card software upgrade via Tftp Unix and Windows Software upgradeCard firmware upgrade using Mupgrade Windows UPS Alarm table Tables of alarms and eventsSTS Alarm table English FrenchUPS event table UPS STS event table 77/81 System alarm table Glossary Telnet Subnet maskTrap Snmp

Related manuals

Manual 18 pages 57.58 Kb