Schneider Electric 66846, 66074 user manual UPS event table

Page 74

Network

Management Card

User Manual

Sources out of synchronization

Déphasage sources 1 / 2

Emergency stop actived

Défaut arrêt d'urgence activ e

Output Thermal overload

Défaut surcharge thermique

Output overload

Défaut surcharge

STS internal fault

Défaut interne

STS general alarm

Défaut Alarme Générale

STS communication failure

Défaut Communication interne

<Sensor name>: Temperature is

<Sensor name>: La température est au

above high threshold xx °C

dessus du seuil haut xx °C

"<Sensor name>: Humidity is above

<Sensor name>: L'humidité est au dessus du

high threshold xx %",

seuil haut xx %",

<Sensor name>: Temperature is below

<Sensor name>: La température est en

low threshold xx °C

dessous du seuil bas xx °C

<Sensor name>: Humidity is below low

<Sensor name>: L'humidité est en dessous du

threshold xx %

seuil bas xx %

<Sensor name>: <Input #1 label>

<Sensor name>: <Input #1 label> <when

<when closed label>

closed label>

<Sensor name>: <Input #1 label>

<Sensor name>: <Input #1 label> <when open

<when open label>

label>

<Sensor name>: <Input #2 label>

<Sensor name>: <Input #2 label> <when

<when closed label>

closed label>

<Sensor name>: <Input #2 label>

<Sensor name>: <Input #2 label> <when open

<when open label>

label>

8.1.3 UPS event table

English

French

Battery fault

Défaut batterie

Battery OK

Fin défaut batterie

Replace battery

Batterie à remplacer

Battery replaced

Batterie remplacée

Low battery

Fin d’autonomie

UPS return from low battery

Fin préalarme d'autonomie

UPS battery charger is not active

Chargeur batterie arrêté

UPS battery charger is active

Chargeur batterie en marche

UPS battery entering minimum

Batterie en charge minimum

condition

 

UPS battery exiting from minimum

Fin batterie en charge minimum

condition

 

Output on battery

Sortie alimentée par batterie

Return on UPS

Sortie sur onduleur

Output on Bypass

Sortie sur Bypass

Bypass : Return on UPS

Sortie sur onduleur

UPS bypass unavailable

Bypass indisponible

UPS bypass available

Bypass disponible

Utility failure

Perte secteur

Utility restored

Retour secteur

Boost activated on UPS

Onduleur en mode Boost

Boost de-activated on UPS

Mode Boost désactivé

UPS overload

Surcharge onduleur

UPS return to normal load

Fin de surcharge onduleur

UPS over temperature

Défaut température

Network Management Card – User Manual

34003676EN/HA

Page 74/81

Image 74
Contents Network Management Card NMC Transverse Environment Sensor Network Management Card MAINTENANCE72 Software Upgrade ConfigurationConfiguration VIA Telnet Configuration VIA SSH Appendices Tables of Alarms and EventsGlossary Network Management Card Connecting the UPS / STS to the NetworkIntroduction Monitoring the UPSs over the network MGE supervisor Enterprise Power ManagerProtecting the computers / servers Network Shutdown module only available for UPS, not for STSConnection How to connect UPS / networkSetting up the protection, for UPS only Presentation of the Network Management Cards NMCSending text messages SMS Presentation of the Environment Sensor solutionDirect sending of E-mail Technical data 10/81 Environment Sensor InstallationBasic configuration Supervision / Administration via a Web browser Optimising the performance of your browserUPS zone general information on the UPS UPS / STSUPS properties UPS status zone essential informationBattery status zone STS status zone essential information STS propertiesSTS zone general information on the STS About Sources status zoneOn-line help 18/81 UPS 3-Phase display Normal input measurementsBattery measurements By Pass measurementsSTS 3-Phase display UPS Control Source 2 input measurement23/81 UPS weekly schedule programming Shutdown parameters Important noteViewing the alarms Logs UPS MeasurementsSTS Measurements 29/81 UPS Event log STS Event log31/81 System log 33/81 Notified events NotificationUPS Email Notification Mail message configuration see next Recipient ListOther settings STS Email NotificationSender Email Message SettingsUPS Email Message Settings SubjectSTS Email Message Settings Email Example Configuration User Name and password by default are MgeupsNetwork Settings 42/81 System 44/81 UPS Notified Applications 46/81 Central Shutdown Configuration STS Notified Applications 49/81 Access control 51/81 Access is disabled and the card is accessible in SSH Time Environment CharacteristicsStatus Configuration Log Environment status 56/81 UPS Environment Settings UPS Environment SettingsSTS Environment Settings Humidity4 Log Set-up of the shutdown parameters Shutdown criteria managed by the Management CardShutdown duration Specific set-up for long autonomy installation 30 mnShutdown when backup time is less than Different server and UPS shutdown sequences 63/81 4 Off/On command Configuring a set of cards with Mupgrade Configuration in local modeChoice 1 Snmp agent configuration menu MgeupsChoice 3 Access control Choice 2 UPS / STS parametersChoice 4 Restore default configuration Choice 5 Reset the cardPuTTY SSH Client Program Configuration via TelnetConfiguration via SSH 70/81 71/81 Card software upgrade via Tftp Unix and Windows Software upgradeCard firmware upgrade using Mupgrade Windows STS Alarm table Tables of alarms and eventsUPS Alarm table English FrenchUPS event table UPS STS event table 77/81 System alarm table Glossary Subnet mask TelnetTrap Snmp
Related manuals
Manual 18 pages 57.58 Kb