APC 420, 650 Battery Replacement Procedure 1000 and 1400 VA models, Storage conditions

Page 18

10.4 Battery Replacement Procedure (1000 and 1400 VA models)

Note: Please read the cautions in section 10.1.

Battery replacement is a safe procedure, isolated from electrical hazards. You may leave the UPS and loads on for the following procedure.

1. Grasp the top of the front cover and tilt it out and down.

2. Unhook the bottom of the cover from the chassis and lift it upward to expose the battery door. Be careful not to strain the ribbon cable. Do not touch the exposed printed circuit board.

3. Fold the front cover on top of the UPS as shown.

4. Use a screwdriver or a coin to r emove the two battery door screws and open the door.

5. Grasp the tab and gently pull the battery out of the UPS.

6. Disconnect the battery leads. Pull the two gray couplers apart to disconnect the battery.

7. Connect the battery leads to the new battery. Note: Small sparks at the battery connectors are normal during battery connection.

8. Slide the battery into the UPS, close the battery door, replace the battery compartment screws, and replace the front cover.

9. Dispose of the old battery properly at an appropriate recycling facility or return it to the sup- plier in the packing material for the new battery. See the new battery instructions for more in- formation.

11.Storage

11.1Storage conditions

Store the UPS covered and upright in a cool, dry location, with its battery fully charged. Before storing, charge the UPS for at least 4 hours. Disconnect any cables connected to the computer in- terface port to avoid unnecessarily draining the battery.

14

Image 18

Contents Smart-UPS v/s Page Contents/Sections/Indice Part Number Revised 11/94 Introduction Thank youPlease save the packaging materials Radio Frequency Interference Theory of OperationIntelligent Battery Management SafetyFeatures Power Management SoftwarePresentation Front panelInspection InstallationRear Panel 650 VA 1400 VAConnect Computer Interface Optional PlacementProtection Strategies Connect Telephone/Network Surge Suppression OptionalConnect to Utility Charge the batteryCheck the Site Wiring Fault Indicator Connect the LoadsOperation Switch On Switch OffShutdown Mode Self-testAlarms OptionsTroubleshooting Wall Mount BracketService Replacing the Battery Replacement BatteriesBattery Replacement Procedure 420 and 650 VA models Battery Replacement Procedure 1000 and 1400 VA models StorageStorage conditions Specifications Extended storageSafety and approvals Computer Interface Port How to Determine On-battery Run Time 1000 VA 1400 VA Load 650 VAMerci Veuillez conserver l’emballage de votre onduleurInterférences radioélectriques Principe de fonctionnementGestion intelligente de la batterie Consignes de sécuritéFonctions Logiciel de gestion électriquePrésentation Panneau avantPanneau arrière 420 et 650 VA 1000 et 1400 VAChoix d’un emplacement Stratégies de protectionChargement de la batterie Branchement de l’interface pour ordinateur en optionBranchement au secteur Branchement des équipementsFonctionnement Vérification du voyant de défaut de câblage de siteMise sous tension et arrêt Mode d’arrêt complet Test automatique de fonctionnementAlarmes Problème Cause possible Solution En cas de problèmeRéparations Français Page Français Conditions de stockage StockageCaractéristiques techniques Stockage longue duréeAppliquée par Ansi C62.41 cat. a ±6 Filtrage dinterférences Page Comment déterminer l’autonomie de la batterie Remarques ¡Importante Introducción¡Gracias ¡Por favor guarde los materiales de embalajeInterferencia con Radio Frecuencia Teoría de OperaciónAdministración Inteligente de la Batería Software de Administración de EnergíaCaracterísticas Seguridad ¡PRECAUCIONPanel Posterior PresentaciónPanel delantero 420 y 650 VAInstalación Inspección1000 y 1400 VA Colocación Estrategias de ProtecciónConexión de la Interfase del Computador Opcional Conexión a la red eléctrica Carga de la bateríaConexión de las cargas Operación Comprobación del Indicador de Fallos de CableadoEncender Apagar Modalidad apagada AlarmasPrueba automática En-bateríaOpciones Detección y solución de problemas Problema Causa posible SoluciónServicio Baterías de reemplazo Procedimiento de reemplazo de baterías modelos 420 y 650 VA Page Condiciones de almacenaje AlmacenamientoEspecificaciones Almacenaje prolongadoPorcentaje de Ansi C62.41 Cat a Serie Interfase Puerto del Computador 13. Cómo determinar el tiempo de operación en-batería Limited Warranty Garantía Limitada

Related manuals

Manual 8 pages 29.77 Kb

Manual 6 pages 273 b