TDK 1500W, 750W technical manual Rear Panel SW1 Setup Switch

Page 38

Table 4-2: Rear panel connections and controls

Number

Item

Description

Section

1

AC input

Wire clamp connector for 1500W units.

3.7.1

connector

IEC connector for 750W units.

3.7.2

 

2

DC output

Bus-bars for 6V to 60V models.

3.9.6

 

 

Wire clamp connector for 80V to 600V models.

 

3

Remote-In

RJ-45 type connector, used for connecting power supplies to

 

 

connector

RS232 or RS485 port of computer for remote control purposes.

7.3

 

 

When using several power supplies in a power system, the first

 

 

7.5

 

 

unit Remote-In is connected to the computer and the remaining

 

 

 

 

 

units are daisy-chained, Remote-In to Remote-Out.

 

4

Remote Out

RJ-45 type connector, used for daisy-chaining power supplies to

7.3

connector

form a serial communication bus.

7.5

 

5

J1 Analog

Connector for remote analog interface. Includes Output Voltage

 

 

Remote

and Current programming and monitoring signals, Shut-off control

 

 

connector

(electrical signal), Enable/Disable control (dry-contact), Power

 

 

 

Supply OK (PS_OK) signal and operation mode (CV/CC) signal.

 

6

SW1 Setup

Nine position DIP-switch for selecting remote programming and

4.4

 

switch

monitoring modes for Output Voltage, Output Current and other

 

 

 

control functions.

 

7

J2 Remote

Connector for making remote sensing connections to the load for

3.10

 

sense

regulation of the load voltage and compensation of load wire drop.

3.8.2

 

connector

 

 

 

 

8

Blank

Blank sub-plate for standard units. Isolated Remote Analog pro-

Fig.4.2

 

Sub-plate

gramming connector for units equipped with Isolated Analog con-

 

 

 

trol option. IEEE connector for units equipped with IEEE pro-

 

 

 

gramming option (shown).

 

9

IEEE switch

Two position DIP-switch for selecting IEEE mode or RS232/RS485

Fig.4.2

 

 

mode when IEEE option is installed.

 

10

Ground

M4x0.7, 8mm long DBL-SEMS screw for chassis ground

Fig.4.2

 

screw

connection.

 

4.4 REAR PANEL SW1 SETUP SWITCH

The SW1 Setup switch (see Fig.4-3) is a 9-position DIP-switch that allows the user to choose the following:

Internal or remote programming for Output Voltage and Output Current.

Remote voltage or resistive programming of Output Voltage and Output Current limit.

Select range of remote voltage and resistive programming.

Select range of output Voltage and Output Current monitoring.

Select the Remote Shut-Off control logic.

Select between RS232 and RS485 communication interface.

Enable or disable the rear panel Enable/Disable control (dry contact).

30

83-507-013 Rev. D

Page 37 Page 39
Image 38
Page 37 Page 39
Contents Genesystm 750W/1500W Page Page Genesys Manual Supplement Table of Contents Front and Rear Panel Controls and Connectors ………...……… Remote Analog PROGRAMMING……………………………………………… Isolated Analog Programming OPTION………………………………… Disclaimer Limitation of WarrantyWarranty Service Trademark InformationSafety Instructions Environmental Conditions SICHERHEITS-INSTALLATIONS Anweisungen Umweltbedingungen Sicherheits-und WarnsymboleAnderungen and Bauteileersatz Introduction Features and optionsGeneral Information General DescriptionAnalog voltage programming and monitoring Multiple output power systemControl via the serial communication port Parallel operationAccessories Specifications ChapterVout Supplemental Characteristics Genesystm 750W & 1500W Power Supplies Outline Drawings Preparation for USE InstallationGeneral Initial InspectionsAC Source Requirements AC Input Power ConnectionLOCATON, Mounting and Cooling Rack Mount Slides optionalAC Input Wire Connection, 1500W models AC Input Connector, 1500W modelsAC Input Connector, 750W models AC Input CordPrior to Operation TURN-ON Checkout ProcedureGeneral OVP Check Constant Voltage CheckConstant Current Check UVL CheckConnecting the Load Wire termination AWGMaking the load connections 6V to 60V Models Noise and Impedance EffectsInductive loads Wire terminal lug 2 places 80V to 600V ModelsLoad wires connection to the output connector Connecting multiple loads, radial distribution method Connecting single loads, local sensing defaultConnecting single loads, remote sensing Multiple load connection with distribution terminals Grounding outputsLocal and Remote Sensing Sense wiringOutput Terminal Grounding Local sensing10.4 J2 sense connector technical information Remote sensingFront and Rear Panel Controls and Connectors Front Panel Controls and IndicatorsAuxiliary Function Rear Panel Connections and Controls Rear panel connections and controlsRear Panel SW1 Setup Switch Resetting the SW1 switch 1 SW1 position functionRear Panel J1 Programming and Monitorng Connector Making J1 connectionsIfcom SignalEnain LocalLocal Operation Constant Voltage ModeConstant Current Mode Over Voltage Protection OVP Setting the OVP levelResetting the OVP circuit Automatic CrossoverFoldback Protection Output SHUT-OFF SO Control VIA Rear Panel J1 ConnectorUnder Voltage Limit UVL Output ON/OFF ControlPsok Signal ENABLE/DISABLE Control VIA Rear Panel J1 ConnectorCV/CC Signal Auto-restart mode Over Temperature Protecton OTPLast Setting Memory Safe-start modeSeries Operation Series connection for increased output voltageSeries connection for positive and negative output voltage Series connection for positive/negative output voltagesParallel Operation Master and Slave units default operation Advanced parallel configurationSetting the units as Master or Slave Connection to the loadAST OFF *OUT OFF To release units from Slave modeCurrent display accuracy Unlocked front panel DAISY-CHAIN ConnectionFront Panel Locking Locked front panelRemote Analog Programming LOCAL/REMOTE Analog IndicationDown Remote voltage programming connectionResisitive Programming of Output Voltage and Current Limit Remote resistive programmingRemote Monitoring of Output Voltage and Current RS232 & RS485 Remote Control ConfigurationFront panel in Remote mode Rear Panel RS232/RS485 Connector6 RS232/RS485 port in Local mode MD Mode SRQ MD Mode Option Factory Installed MD Mode DescriptionMD Mode enable Serial communication mode MD Mode SRQ RetransmissionConnecting Power Supplies to RS232 or RS485 BUS Single power supplyCommunication Interface Protocol Error Messages Command SET DescriptionOutput Control Commands Initialization Control CommandsID Control Commands FILTER? DVC?Filter OUT?Global Output Commands Disable SRQ retransmission MD Mode Option Required Single Byte CommandsEnable MD Mode MD Mode Option Required Enable SRQ retransmission MD Mode Option RequiredTest if MD Mode is Installed Addressed commands with response Read registersPrint Power On Time Addressed commands without response Acknowledge SRQ1010 None Disable retransmission of SRQs by GEN750W models GEN1500W models Current programming range STATUS, Error and SRQ Registers 10.6 Status Control CommandsConditional Registers Status RegistersService Request Enable and Event Registers BITFault Enable Register Fault Event RegisterStatus Enable Register Status Event RegisterCommunication Test Power supply set-upSerial Communication Test SET-UP 1 0-5V/0-10V Option PN IS510 SpecificationsIsolated Analog Programming Option PPM/CIsolated Programming & Monitoring Connector Setup and Operating Instructions Maintenance Fuse Rating OUP
Top Page Image Contents