TDK 1500W, 750W technical manual Isolated Analog Programming OPTION…………………………………

Page 8

TABLE OF CONTENTS

7.10.6 Status Control Commands………………………………………………………………..

Pg. 62

7.11 STATUS, ERROR AND SRQ REGISTERS…………………………………………………..

Pg. 62

7.11.1 General Description………………………………………………………………………..

Pg. 62

7.11.2 Conditional Registers………………………………………………………………………

Pg. 63

7.11.3 Service Request: Enable and Event Registers………………………………………….

Pg. 64

7.12 SERIAL COMMUNICATION TEST SET-UP.………………………………………………….

Pg. 67

CHAPTER 8 ISOLATED ANALOG PROGRAMMING OPTION…………………………………

Pg. 68

8.1 INTRODUCTION……………………………………………………………………………………

Pg. 68

8.2 SPECIFICATIONS………………………………………………………………………………….

Pg. 68

8.2.1 0-5V/0-10V option……………………………………………………………………………

Pg. 68

8.2.2 4-20mA option………………………………………………………………………………..

Pg. 68

8.3 ISOLATED PROGRAMMING & MONITORING CONNECTOR………………………………

Pg. 69

8.4 SETUP AND OPERATING INSTRUCTIONS……………………………………………………

Pg. 70

8.4.1 Setting up the power supply for 0-5V/0-10V Isolated Programming and Monitoring…

Pg. 70

8.4.2 Setting up the power supply for 4-20mA Isolated Programming and Monitoring……..

Pg. 70

CHAPTER 9 MAINTENANCE………………………………………………………………………...

Pg. 71

9.1 INTRODUCTION……………………………………………………………………………………

Pg. 71

9.2 UNITS UNDER WARRANTY……………………………………………………………………...

Pg. 71

9.3 PERIODIC MAINTENANCE……………………………………………………………………….

Pg. 71

9.4 ADJUSTMENT AND CALIBRATION……………………………………………………………..

Pg. 71

9.5 PARTS REPLACEMENT AND REPAIRS………………………………………………………..

Pg. 71

9.6 TROUBLESHOOTING……………………………………………………………………………..

Pg. 71

9.7 FUSE RATING……………………………………………………………………………………...

Pg. 72

83-507-013 Rev. D

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Genesystm 750W/1500W Page Page Genesys Manual Supplement Table of Contents Front and Rear Panel Controls and Connectors ………...……… Remote Analog PROGRAMMING……………………………………………… Isolated Analog Programming OPTION………………………………… Limitation of Warranty Warranty ServiceDisclaimer Trademark InformationSafety Instructions Environmental Conditions SICHERHEITS-INSTALLATIONS Anweisungen Umweltbedingungen Sicherheits-und WarnsymboleAnderungen and Bauteileersatz Features and options General InformationIntroduction General DescriptionMultiple output power system Control via the serial communication portAnalog voltage programming and monitoring Parallel operationAccessories Specifications ChapterVout Supplemental Characteristics Genesystm 750W & 1500W Power Supplies Outline Drawings Installation GeneralPreparation for USE Initial InspectionsAC Input Power Connection LOCATON, Mounting and CoolingAC Source Requirements Rack Mount Slides optionalAC Input Connector, 1500W models AC Input Connector, 750W modelsAC Input Wire Connection, 1500W models AC Input CordPrior to Operation TURN-ON Checkout ProcedureGeneral Constant Voltage Check Constant Current CheckOVP Check UVL CheckConnecting the Load Wire termination AWGMaking the load connections 6V to 60V Models Noise and Impedance EffectsInductive loads Wire terminal lug 2 places 80V to 600V ModelsLoad wires connection to the output connector Connecting multiple loads, radial distribution method Connecting single loads, local sensing defaultConnecting single loads, remote sensing Multiple load connection with distribution terminals Grounding outputsSense wiring Output Terminal GroundingLocal and Remote Sensing Local sensing10.4 J2 sense connector technical information Remote sensingFront and Rear Panel Controls and Connectors Front Panel Controls and IndicatorsAuxiliary Function Rear Panel Connections and Controls Rear panel connections and controlsRear Panel SW1 Setup Switch Resetting the SW1 switch 1 SW1 position functionRear Panel J1 Programming and Monitorng Connector Making J1 connectionsSignal EnainIfcom LocalLocal Operation Constant Voltage ModeConstant Current Mode Setting the OVP level Resetting the OVP circuitOver Voltage Protection OVP Automatic CrossoverOutput SHUT-OFF SO Control VIA Rear Panel J1 Connector Under Voltage Limit UVLFoldback Protection Output ON/OFF ControlPsok Signal ENABLE/DISABLE Control VIA Rear Panel J1 ConnectorCV/CC Signal Over Temperature Protecton OTP Last Setting MemoryAuto-restart mode Safe-start modeSeries Operation Series connection for increased output voltageSeries connection for positive and negative output voltage Series connection for positive/negative output voltagesParallel Operation Advanced parallel configuration Setting the units as Master or SlaveMaster and Slave units default operation Connection to the loadAST OFF *OUT OFF To release units from Slave modeCurrent display accuracy DAISY-CHAIN Connection Front Panel LockingUnlocked front panel Locked front panelRemote Analog Programming LOCAL/REMOTE Analog IndicationDown Remote voltage programming connectionResisitive Programming of Output Voltage and Current Limit Remote resistive programmingRemote Monitoring of Output Voltage and Current RS232 & RS485 Remote Control ConfigurationFront panel in Remote mode Rear Panel RS232/RS485 Connector6 RS232/RS485 port in Local mode MD Mode Option Factory Installed MD Mode Description MD Mode enable Serial communication modeMD Mode SRQ MD Mode SRQ RetransmissionConnecting Power Supplies to RS232 or RS485 BUS Single power supplyCommunication Interface Protocol Error Messages Command SET DescriptionOutput Control Commands Initialization Control CommandsID Control Commands DVC? FilterFILTER? OUT?Global Output Commands Single Byte Commands Enable MD Mode MD Mode Option RequiredDisable SRQ retransmission MD Mode Option Required Enable SRQ retransmission MD Mode Option RequiredAddressed commands with response Read registers Print Power On TimeTest if MD Mode is Installed Addressed commands without response Acknowledge SRQ1010 None Disable retransmission of SRQs by GEN750W models GEN1500W models Current programming range STATUS, Error and SRQ Registers 10.6 Status Control CommandsConditional Registers Status RegistersService Request Enable and Event Registers BITFault Enable Register Fault Event RegisterStatus Enable Register Status Event RegisterCommunication Test Power supply set-upSerial Communication Test SET-UP Specifications Isolated Analog Programming Option1 0-5V/0-10V Option PN IS510 PPM/CIsolated Programming & Monitoring Connector Setup and Operating Instructions Maintenance Fuse Rating OUP
Top Page Image Contents