TDK 1500W, 750W technical manual None Disable retransmission of SRQs by

Page 68

Table 7-3. SINGLE BYTE COMMUNICATIONS

Name

Bit Positions

Response

Description

 

 

 

 

Global

 

 

 

Commands

 

 

 

Disable MD Mode

1010 0000

None

Set supplies out of MD Mode (default)

 

 

 

 

Enable MD Mode

1010 0001

None

Set supplies into MD Mode

 

 

 

 

Disable SRQ

1010 0010

None

Disable retransmission of SRQs by

retransmission

 

 

supplies (default)

Enable SRQ

1010 0011

None

Enable retransmission of SRQs by

retransmission

 

 

supplies

Enable FLT Bit

1010 0100

None

Enable the FLT bit in the SENA Reg-

 

 

 

ister

 

 

 

 

Disconnect serial

1011 1111

OK

All supplies will halt transmission and

communications

 

 

enter the non-addressed state.

Addressed

 

 

 

Commands

 

 

 

Read Registers

100x xxxx

Register data

Non destructive read of all register. x

 

 

 

xxxx is the address of the supply in

 

 

 

binary.

Re-enable SRQ

Byte 1

None

Re-enable SRQ without reading or

 

1010 0101

 

clearing the SEVE Register. xxxx xxxx

 

Byte 2

 

is the address of the supply in binary.

 

xxxx xxxx

 

Works only in MD Mode.

Print Power On

Byte 1

Power On time

Read the time the supply is active un-

Time

1010 0110

in minutes

der AC Power. xxxx xxxx is the ad-

 

Byte 2

 

dress of the supply in binary. Returns a

 

xxxx xxxx

 

32 Bit integer as 8 Hex bytes. A ‘$’

 

 

 

sign is appended to the data followed

 

 

 

by a 2 byte check-sum. A total of 11

 

 

 

bytes are returned.

Retransmit last

110x xxxx

Last message

Retransmit last response from a com-

message

 

 

mand. x xxxx is the address of the

 

 

 

supply in binary.

Acknowledge

111x xxxx

None

Acknowledge SRQ. If retransmission

SRQ

 

 

of SRQ is enabled, it will remain en-

 

 

 

abled for the next SRQ. X xxxx is the

 

 

 

address of the supply in binary.

Test if MD Mode

Byte 1

0 or 1

Returns a 0 if not installed or a 1 if in-

is Installed

1010 1010

 

stalled. A ‘$’ sign followed by a 2 bytes

 

Byte 2

 

checksum and Carriage Return is ap-

 

xxxx xxxx

 

pended to the data. xxxx xxxx is the

 

 

 

address of the supply in binary.

Supply Initiated

 

 

 

Communications

 

 

 

SRQ

100x xxxx

N/A

SRQ from supply when in MD Mode. X

 

 

 

xxxx is the address of the supply in

 

 

 

binary.

60

83-507-013 Rev. D

Image 68
Contents Genesystm 750W/1500W Page Page Genesys Manual Supplement Table of Contents Front and Rear Panel Controls and Connectors ………...……… Remote Analog PROGRAMMING……………………………………………… Isolated Analog Programming OPTION………………………………… Limitation of Warranty Warranty ServiceDisclaimer Trademark InformationSafety Instructions Environmental Conditions SICHERHEITS-INSTALLATIONS Anweisungen Umweltbedingungen Sicherheits-und WarnsymboleAnderungen and Bauteileersatz Features and options General InformationIntroduction General DescriptionMultiple output power system Control via the serial communication portAnalog voltage programming and monitoring Parallel operationAccessories Specifications ChapterVout Supplemental Characteristics Genesystm 750W & 1500W Power Supplies Outline Drawings Installation GeneralPreparation for USE Initial InspectionsAC Input Power Connection LOCATON, Mounting and CoolingAC Source Requirements Rack Mount Slides optionalAC Input Connector, 1500W models AC Input Connector, 750W modelsAC Input Wire Connection, 1500W models AC Input CordPrior to Operation TURN-ON Checkout ProcedureGeneral Constant Voltage Check Constant Current CheckOVP Check UVL CheckConnecting the Load Wire termination AWGMaking the load connections 6V to 60V Models Noise and Impedance EffectsInductive loads Wire terminal lug 2 places 80V to 600V ModelsLoad wires connection to the output connector Connecting multiple loads, radial distribution method Connecting single loads, local sensing defaultConnecting single loads, remote sensing Multiple load connection with distribution terminals Grounding outputsSense wiring Output Terminal GroundingLocal and Remote Sensing Local sensing10.4 J2 sense connector technical information Remote sensingFront and Rear Panel Controls and Connectors Front Panel Controls and IndicatorsAuxiliary Function Rear Panel Connections and Controls Rear panel connections and controlsRear Panel SW1 Setup Switch Resetting the SW1 switch 1 SW1 position functionRear Panel J1 Programming and Monitorng Connector Making J1 connectionsSignal EnainIfcom LocalLocal Operation Constant Voltage ModeConstant Current Mode Setting the OVP level Resetting the OVP circuitOver Voltage Protection OVP Automatic CrossoverOutput SHUT-OFF SO Control VIA Rear Panel J1 Connector Under Voltage Limit UVLFoldback Protection Output ON/OFF ControlPsok Signal ENABLE/DISABLE Control VIA Rear Panel J1 ConnectorCV/CC Signal Over Temperature Protecton OTP Last Setting MemoryAuto-restart mode Safe-start modeSeries Operation Series connection for increased output voltageSeries connection for positive and negative output voltage Series connection for positive/negative output voltagesParallel Operation Advanced parallel configuration Setting the units as Master or SlaveMaster and Slave units default operation Connection to the loadAST OFF *OUT OFF To release units from Slave modeCurrent display accuracy DAISY-CHAIN Connection Front Panel LockingUnlocked front panel Locked front panelRemote Analog Programming LOCAL/REMOTE Analog IndicationDown Remote voltage programming connectionResisitive Programming of Output Voltage and Current Limit Remote resistive programmingRemote Monitoring of Output Voltage and Current RS232 & RS485 Remote Control ConfigurationFront panel in Remote mode Rear Panel RS232/RS485 Connector6 RS232/RS485 port in Local mode MD Mode Option Factory Installed MD Mode Description MD Mode enable Serial communication modeMD Mode SRQ MD Mode SRQ RetransmissionConnecting Power Supplies to RS232 or RS485 BUS Single power supplyCommunication Interface Protocol Error Messages Command SET DescriptionOutput Control Commands Initialization Control CommandsID Control Commands DVC? FilterFILTER? OUT?Global Output Commands Single Byte Commands Enable MD Mode MD Mode Option RequiredDisable SRQ retransmission MD Mode Option Required Enable SRQ retransmission MD Mode Option RequiredAddressed commands with response Read registers Print Power On TimeTest if MD Mode is Installed Addressed commands without response Acknowledge SRQ1010 None Disable retransmission of SRQs by GEN750W models GEN1500W models Current programming range STATUS, Error and SRQ Registers 10.6 Status Control CommandsConditional Registers Status RegistersService Request Enable and Event Registers BITFault Enable Register Fault Event RegisterStatus Enable Register Status Event RegisterCommunication Test Power supply set-upSerial Communication Test SET-UP Specifications Isolated Analog Programming Option1 0-5V/0-10V Option PN IS510 PPM/CIsolated Programming & Monitoring Connector Setup and Operating Instructions Maintenance Fuse Rating OUP